Jump to content

jbojo

Benefactors
  • Content Count

    3729
  • Joined

  • Last visited

  • Days Won

    10

jbojo last won the day on February 17 2016

jbojo had the most liked content!

Community Reputation

98 Excellent

4 Followers

About jbojo

  • Rank
    Mustang Guru

Vehicle Info

  • Vehicle(s)
    1973 Mustang Mach 1 Q code C6 tranny

Location

  • Location
    Richland, WA
  • Region
    Northwest

Personal Information

  • Sex
    Undisclosed
  1. Enjoy your trip!!! The Great Ocean Road is a not to miss site seeing trip. If you schedule a tour with a company I would recommend Oceania Tours and Safaris and ask for Ricarda. She does a great tour and takes you to places that others often miss.
  2. My 5 speed tranny was delivered today and took 4 yrs to get but I think it was worth the wait. The shifter was moved back 6 inches and raised by about the same amount by using a dogbone plate mounted on the front mounting point to get the proper placement.. This was unique to the Roadrunners with bench seats from 1971 on. The .70 overdrive and 4.10 rear should work well together on the freeways. All B and E body cars with bucket seats had the shifter mounted to the tailshaft either in the forward or rear spot.
  3. My 73 was made on 6/28/1973 I was 22 when it was made and bought it on 9/20/73
  4. I have one, it is powered coated gray. I'll see if I can get a pic if you are interested. Mine is actually a dark gray/black never installed. It is an Edelebrock Torker for 351C 4v, a little dusty from being stored for a few years. Attached a top and bottom pic.
  5. I have one, it is powered coated gray. I'll see if I can get a pic if you are interested.
  6. They are molded so I believe that it is plastic. They do make these grips in other materials such as carbon fiber and other shades of wood. Just an FYI they also have the old shifters used in Mustangs if you anyone is in the market for a replacement.
  7. Tires that I plan to use are: FRT - G60-15 Goodyear Rear - L60-15 Goodyear Rims will be Black steel that were standard for the car with hubcaps. Car will look something like this with a half black vinyl top and turn down exhausts, not the machine gun type that many of these cars had. Color is Curious Yellow. What do you guys think?
  8. Here is an original A833 tranny. You really can't tell the difference between the new 5 speed and the old 4 speed if you don't look at them closely. The obvious difference is that the new has an aluminum casing while the old is steel. What they did was to design the overdrive gear to use the reverse lever so they maintained the same appearance, that lever has 2 functions instead of 1 now. The benefit is that besides keeping the original looks you don't have to chop up the cars tunnel to install the other 5 and 6 speed trannies that are available now.
  9. I found the shifter that I needed. Hurst is now producing them again and was able to get the bench seat model that I needed. It was actually cheaper to buy the new one than to have the old one re-chromed. Also was able to get the correct lens for the shift pattern from them. These parts will be in next week.
  10. I plan to document the build for this as I go along. I can't believe that it took 4 yrs for this to be produced and so far only less than 100 have been made for A and E bodies. This is one of the first RR ones to be made for a bench seat model (B body), most are for the bucket seat ones..
  11. After a 4 yr wait I finally got an A 855 5 speed tranny for my RR project. With a .70 OD the 4.10 rear will be freeway friendly when this project is completed. I will be turning 2330 @70mph with the 4.10 rear axle.
  12. Have you thought of just replacing it? I think they run around $30 or so. Check with Don at Ohio Mustang and he can tell you if it is close to the original in looks and design. I went that route when I replaced mine and they were similar in looks..
  13. Sounds like the brake proportioning valve could be bad too. That is the unit that causes the brake light to come on when brake pressures are not the same in all lines. There is a rod/piston inside that unit that is usually centered in the valve body. If the pressure is higher on one side if forces the rod to move off center and the light to come on. There are springs inside that can get gummed up that prevents the rod from centering after it ages. There are rebuild kits available or you can just buy a new one. When I went 4 wheel disk I had to change my disk/drum one to disk/disk and they run around $100 or so and make sure you get the right one. The other unit to suspect is the master cylinder, there are rebuild kits for that too. There is also a rod with a couple of o rings that can wear and cause pressure going to the proportional valve to be higher on one side than the other. There are two lines from the master cylinder going to the proportional valve, one line to each side of the piston and the pressures should be equal. I would check the master cylinder first and then the proportional valve.

About Us

7173Mustangs.com is a community forum designed especially for fans and owners of the 1971, 1972 and 1973 Ford Mustang! We are not affiliated with Ford Motor Company in any way.

Site Navigation

Forums
Gallery
7173 Wiki
Blogs
Clubs

7173logo_small.png

Site Info

Founded:
July 2010

By:
Webfinity Design

From:
Latrobe, PA

×
×
  • Create New...

Important Information

We have placed cookies on your device to help customize your user experience here on 7173Mustangs.com. You can adjust your cookie settings to your preferences if you like, otherwise we'll assume that you're okay to continue.