Jump to content

Nelsonlucero

Members
  • Posts

    43
  • Joined

  • Last visited

Everything posted by Nelsonlucero

  1. Hello, The needle tach fell off. For a while now the tach was getting stuck and now the needle fell off. Any suggestions ? Thank you, NL
  2. Hi there, There have been quite a few posts posted on this very subject over the years with the Forum. Try the search engine for some good feedback and help. Here are some links to get you started.::thumb:: http://www.7173mustangs.com/thread-fix-for-dim-71-to-73-mustang-dash-instrument-panel-lights http://www.7173mustangs.com/thread-instrument-panel-light-sockets http://www.7173mustangs.com/thread-advancements-in-led-lighting-2014 Cheers, Greg.:) I find myself having the same issue... I was going to start a new post but decided to join this thread instead. I even replaced all light bulbs with LEDs and new sockets. I am still not happy with the brilliance of the cluster... Lights did not work when I first replaced all bulbs and had to mess with them for a while before they worked... I am now thinking that I may try a new circuit board but was hoping for an opinion before I go and spend another $100.00. Any advice ? Thank you. Nelson.
  3. I would say you will pay $400 -$500 for gaskets/bearings/ and syncro bushings. Of course it becomes al-a-cart based on what is worn out. I think you need to plan on $1100 as a median price for what it may cost you. Contact David Kee Toploaders to see what the swap price is there for a rebuilt. kcmash Thank you !
  4. I would say you will pay $400 -$500 for gaskets/bearings/ and syncro bushings. Of course it becomes al-a-cart based on what is worn out. I think you need to plan on $1100 as a median price for what it may cost you. Contact David Kee Toploaders to see what the swap price is there for a rebuilt. kcmash Thank you very much !
  5. Hello, I noticed that my manual transmission drops out of 3rd. gear just by the vibration of the car ... Similarly, the shifter drops a bit when the car is put in reverse but does not fall "out" as it happens on 3rd. gear. Does anyone have any suggestions ? How much should I expect to pay for a complete rebuild if I go that route? Thank you. Nelson.
  6. Hello, Does someone have this for sale of know here I can find one ? Thank you. Nelson.
  7. Thanks so much ! Thank you all of you for your great insight ! Will add pics of finished product hopefully soon ...
  8. fantastic... Thank you very much ! Any idea where I can find the rod retainers for the last bow ?
  9. Hello, I am trying to determine whether I have all parts needed to get my headliner installed. So far I have: 1- headliner 2- sail panels 3- headliner bows 4- wind lace 5 - headliner rod retainer (1piece) . I think I am missing one more. 6- tack strips are in a box... Where do these go ? Any comments, pictures, diagrams are most appreciated. Many thanks, Nelson.
  10. Hello, I am trying to replace my original steering wheel with a grant removable steering wheel security system. I find that the post (bolt ) sticks out too far from the nut that holds the original steering wheel in place and therefore the grant system hub does not go all the way into place. Is there an adjustment that I can make so that the bolt does not stick out so far ? Many thanks for your input. NL
  11. That is a piece of trim use in the rear seat area It fills in the area between the seat upright section and interior quarter panel Thank you.
  12. Hello, Does anyone know what this is? I found it in a box of parts needs to compete my restoration. Any help is most appreciated ! Thank you, Nelson.
  13. Hello, I just picked up my car for final shakedown before interior goes in and it's finally done! I noticed that there is a lot of Shake on the outside mirrors as I drive down the road. However, once parked, it seems that the mirrors are holding tight. I have another card of a different make that has similar mirrors and I don't notice nearly the same amount of Shake... Does anyone have some input ? Thank you very much in advance. Nelson.
  14. Interested in a black long console in really good shape... Do you have one still ? Thank you, Nelson.
  15. Hi All, Does anyone know where I can locate these bezels ? I am very close to completing the restoration and mine look really bad. Thank you. NL
  16. Hello, I am looking for three switch bezels including knobs: 1- lights 2- lighter 3- wiper NOS or like new condition. Does anyone have ? Thank you, Nelson.
  17. Hello, I am looking for a set of silver / black headlight bezels for a 1973 Mach 1. New or like new condition if possible. Thank you, Nelson.
  18. Great thanks... Looking forward to receiving them. Nelson.
  19. Looking for 73 mach 1 trap door hinge and a couple of other pieces... Please see picture attached and let me know if you have any... Thank you,
×
×
  • Create New...