Jump to content


  • Posts

  • Joined

  • Last visited

Everything posted by Wilco549

  1. I'm about 99% sure the MM and frame perches are different.. The T-bird uses the wider mounts that were in LTD and other large corp cars. I'm putting a 70 LTD motor in mine and have ran into this issue myself. Basically, the LTD type mount is wider f-r by about 1" and are offset too much to put the engine, tranny in the right location. Picture below may help you identify them. https://www.rockauto.com/en/moreinfo.php?pk=315289&cc=1139802&jsn=12 is the LTD, T-Bird mount https://www.ebay.com/p/1971-1972-1973-Ford-Mustang-429-CJ-460-6-Peice-Motor-Mount-Kit-Full-Set-Mounts/15021035339?iid=392074353185&_trkparms=aid%3D222007%26algo%3DSIM.MBE%26ao%3D2%26asc%3D20131003132420%26meid%3D8ecb0773c1964eb488e893d477b000fd%26pid%3D100005%26rk%3D1%26rkt%3D5%26sd%3D162796297710%26itm%3D392074353185&_trksid=p2047675.c100005.m1851 appears to be the correct MM for the Mustang.
  2. I'm putting the 460 Performer in mine. It was highly recommended by the "pros" over at the 429-460 forum. Stock height.
  3. https://winchester.craigslist.org/pts/d/1971-mustang-parts-car/6420107421.html Not mine, Near DC
  4. 429=460 Police Interceptor High flow manifolds. No cracks or repairs. Perfect for Mustangs, Galaxie, Cougar and everything else with a tight fit. Has the steering gear notch for Mustangs. As far as I can tell they are basically the same as the D1ZE-9431-CA2 71 Mustang 429 CJ 4V manifolds with slightly smaller ports{1.5x2.25} d30e-9430-ba d30e-9431-ba $500 + shipping for set with High Temp 2000d Coating $350 + shipping for set raw without sandblast/coating I'm just selling one set.
  5. I may be able to help you out if the others don't work out. Where you located? Sent from my VS986 using Tapatalk
  6. Don, I'm pretty sure those FE Mounts will not work on the 385 series 429-460 engine. Sent from my VS986 using Tapatalk
  7. Thanks! I've updated the original post with what I really need. :D
  8. OK, I'm confused now. I'm putting a 429 in a 351C car. The 429 mounts on the engine are 1pc each side , 3 bolts to engine requiring 4 1/2" perch width. The perches on the car are 3 1/2" wide which I believe require the 2pc mounts that attach to block with only two bolts. The service manual is not clear [to me] as to which is correct. I look up MM's on the part site rockauto and it shows the wider, 3 bolt mounts are correct. Do I need new, wider perches for the 429? Help!
  9. 71-72. I'm not looking for the rubber mounts. I need the frame perches, supposedly they allow the engine to sit 1/2" lower (any V8) for convertible? I cant verify that. Also looking for 429/460 engine mounting brackets that the rubber mounts attach to on the block. I can buy them new for about 130.........but I'm cheap!
  10. Let me know what you have (Private MSG please) with shipping to 37743. I need the lower sitting convertible frame perches (Engine Mounts). I need the 429 brackets that attach to the block. [block plates] Also, I have parts to trade if you need something for your build. Tim
  11. You have the frame perches for the 72 conv? If so, Cost + shipping to 37743? Tim PS. Your PM folder is full. Would not accept my PM.
  12. CJ Pony here in the US has their New Vintage units on sale for $510 usd. https://www.cjponyparts.com/new-vintage-usa-gauge-kit-performance-series-electronic-speedometer-1971-1973/p/IBK714-V/ Not sure if they have the international units on sale. I've not used them but they look nice.
  13. Just want to reiterate what OZ stated. The 170 d angles are not correct. I'm working on installing mine and the width offset is about 4" making to plan st 170. It should be 2". Fit before welding. It appears the vertical is correct.
  14. Thanks! Will do. Sent from my VS986 using Tapatalk
  15. Not show quality, they don't have to be perfect. Manual windows. Black preferred but I could dye them black I suppose.
  16. Looking for headers for mild performance build. Not interested in the long tubes that wrap under the cross-member. Send me a PM if you have anything. Tim
  17. Not mine: https://evansville.craigslist.org/wto/d/magnum-500-wheels/6299208207.html
  18. Sorry guys! I've pretty much decided to keep it. I was originally going to go with a classic air or similar system on mine but I'm thinking now I'd be better off using the system off of the parts car. Is there any way to delete my original post?
  19. Any interest in the complete AC system on a 72, 351C? I bought a parts car with a 1/2 engine but the AC appears to be sealed and intact. Will not ship.
  20. 1970 D0VE engine w/ D0VE-C heads, 4b intake. No longer available!
  21. I know this is an old thread but just wondering if the OP did buy those. Also, are these a good option at mustangmarket.com
  • Create New...