Jump to content


  • Content Count

  • Joined

  • Last visited

Community Reputation

3 Neutral

About mustangandy

  • Rank
    Mustangs are cool

Vehicle Info

  • My Car
    1971 Cobra Jet 429 Ram Air C6 auto 3.50 traction loc


  • Location
  • Region

Personal Information

  • Sex
  1. Thanks Canted393. I've emailed them
  2. Hi all. A long shot I'm sure but if I don't ask! I'm after a fan shroud for my 1971 mustang 429 CJ. Its the same as the Torino 429 CJ. Ford part # DOOZ 8146D. A repro is fine and doesn't have to be new at that, so long as the condition is ok. The other thing is that I live in central France 86290 so it would need shipping there. Thanks in advance and here's hoping :-) Cheers Andy
  3. Thing with the Quickjack, which I looked at and rejected, is that I couldn't see that you could line the lift up in line with the body as the front and rear jacking points are not parallel together as the front is more inboard than the rear. As the Quickjack tilts backwards when lifting this means that the lifts on each side of the car are going in opposite directions as the car lifts which I didn't think would work. If you could place them parallel front and back then yes sure they would. I ended up going with a pair of these (so four individual lifts working as 2 pairs front and back) as the
  4. Hi, I'm sorry but not sure I follow your last sentence. What parts (and their location) are you referring to? Many thanks Andy
  5. This is my mach 1 ram air. It's been repainted but it's to the original spec as far as I know comment ajouter une photo sur facebook sans créer d album
  6. I haven't done this before so guess I did stuff it up unfortunately. I presume the valve body will have to come out again then? Cheers Andy
  7. The ram air filter (at least on the 429) is 3 inches tall
  8. The car is level on the ramps. I won't top up, don't want to overfill but as I have to pull the pan again anyway...... The shifter will move from Park to Reverse, just about, but no further than that so no other positions. I presume that I'd need to drop the valve body again to re-install? Thought I'd done it correctly but guess I can't have. I know there's other causes for a stuck tranny but as I only removed the valve body to do the shift kit then I must have done something wrong when refitting it. I am quite sure that I replaced all the springs, balls, valves etc properly (t
  9. Just checked the dipstick (should have done it before) and there's less than one cm showing. I know it should only be about half way up the little holes when cold but sounds a little low? As she's still on ramps I can't run her up hot to check. Would you suggest I top up a little first? Cheers again Andy
  10. Thanks Hemi. Bugger, I followed all the instructions so was confident that I had swapped the springs etc over correctly and reassembled and reinstalled as I should have. But it sounds like there is more to it than just that which was not included in the Transgo notes? Cheers Andy
  11. Help guys! My 71 mustang has a C6 auto transmission. Nine months ago I ramped her to do some maintenance work. I did a transmission flush (7L of ford ATF) and changed the filter. I put in a Transgo 67 1-2 shifter kit too, a new vacuum modulator, a shorter pin and turned the adjustment screw a few turns in. She stayed on the ramps as it was then very wet here and coming up to winter. I was also waiting for a new, correct style exhaust system from the USA which took a while. Fitted now. I then removed the shifter mechanism from the car to insert new bushes into the lever as the action was
  12. Get the most powerful battery that will fit. I got a varta 850 cca one (for my 429CJ)
  13. Hi All, Been a while and still working my way through a comprehensive servicing of my 429 CJ RA C6 Mach 1. Life gets in the way, as it does, and it's only recently that I've got a set of lifts to give me semi decent working room under the car. I just cleared some oil and crud from the engine block (a few leaks to take care of) and noticed (of the ones that are easily seen) that 3 of the core plugs are brass. I presume, therefore, that all 6 will be replacements and that it must mean that the engine has been removed at some point in its life? From what I've been able to work out
  14. If you don't have to get headers there's always the cast iron interceptor manifolds (not CJ/SCJ ones) as much cheaper and shouldn't really give up much in the way of performance compared with the ford shorties?
  • Create New...