Jump to content

The Rickster - a 73 Mach 1 work in progress


Recommended Posts

Well, since my 73 Coupe burned, I've been working on getting another project. I was able to find a 73 Mach 1, and last weekend, my wife and I drove to eastern Tennessee and picked it up.

 

IMAG0021_zpsesfzfpos.jpg

 

Yesterday, I was able to clean it out, and vacuum the trash from the floor to see just what I have. Well, I have a lot of work ahead of me, it what I have. The core support is bent and needs to be replaced.

IMAG0040_zps4o1p0wl6.jpg

 

The front right inner fender is rusted through under the battery tray.

IMAG0062_zpsindzih5x.jpg

 

It has frame mounts welded in for an unidentified type of motor, and I discovered today that the center section of the engine crossmember was cut out and modified. When I removed the front bumper, I found the front left mounting hole was bent and torn, and the capture nut for therear bolt for that bumber bracket is not longer captured. :(

IMAG0054_zpsqi9z9upb.jpg

 

The cowl appears to be okay. That is, until I poured some water into the vents on top and discovered water pouring into the passenger toekick.

IMAG0061_zpstbbvjogk.jpg

 

The left and right side floors need to be replaced, along with both front extensions. In the back seat area, both sides also have a bunch of rust that was partially covered with fiberglass.

IMAG0058_zpso3niqirt.jpg

 

The trunk floor was covered with a sheet of galvanized sheet, that when removed, revealed about 1/2 of the trunk floor rusted out.

IMAG0041_zps3qdm8sdr.jpg

 

The trunk floor extensions, outer wheel houses, and both rear quarter panels also have significant rust and need to be replaced.

IMAG0050_zpszgcwiflg.jpg

 

The taillight panel also was extensively rusted.

IMAG0051_zps3pdpaos9.jpg

 

Both quarters are rusted, and the passenger side has about over 1/2 of Bondo where it was seriously caved in.

 

The passenger door bottom is completely rotten. I haven't taken the drivers side door off yet, but I did see a little bit of rust on the rear corners, sooo....

IMAG0070_zpst1rzbi5g.jpg

 

So now you've met my new Mach 1 project. I'm calling it Rusty, a name that really seems to fit it at this point. I've really got a lot of work ahead of me. I'm thinking a road trip to visit Don at OMS may be in my future.

Ron

The Rickster, a 1973 Mach 1, being restored as a tribute to my brother who passed away with COVID in July 2020.

Billy, a 1976 Ford Bronco, also needs a lot of work.

El Guapo, a 1986 F150, frame-off Resto-Mod.

Also, in the queue, a 1950 Ford F1 Panel truck and 1962 Falcon Ranchero

Link to comment
Share on other sites

You definitely have your hands full. Look at it this way. This project will keep you out of the bars!!! Good luck. I'm looking forward to your progress reports!!

- Travis

 

 

 

I'm an analog man in a digital world.

Link to comment
Share on other sites

Eric (Mister 4x4) will have lot of pointers for ya!

His car has come a LONG way!

 

Ray

1971 Boss 351  

1972 Q code 4 speed convertible 

1971 Mustang Sportsroof  351-2V FMX 

1971 Hardtop (parts car)

1973 Mach 1 (parts car)

Link to comment
Share on other sites

Wow, when I posted all my pictures of the 1972 Mustang I was thinking I had a lot of rust. Good to see I have good company. Keep the pictures coming! Love seeing new metal replacing rusty metal!

Link to comment
Share on other sites

Well, the good news is I don't have to make a profit doing this. I'm doing it for fun, but I hadn't expected this much fun to be in my future. ;) Thanks for the encouragement, guys. I'll keep the thread updated as I progress.

Ron

The Rickster, a 1973 Mach 1, being restored as a tribute to my brother who passed away with COVID in July 2020.

Billy, a 1976 Ford Bronco, also needs a lot of work.

El Guapo, a 1986 F150, frame-off Resto-Mod.

Also, in the queue, a 1950 Ford F1 Panel truck and 1962 Falcon Ranchero

Link to comment
Share on other sites

You have alot of work ahead of you. Good thing to know you have alot of the tools and equipment to get you there. Keep at it and don't loose sight of the goal. There will probably be some bad days ahead, but keep plugging away at it. Give me a call when you need an extra set of hands. Next time I will be more reliable than the last time for the unload.

BKDunha

72 Mach 1 H-Code (Concourse driven restoration)

67 S-Code Factory GT with 4-Spd

68 Mercury Cyclone (Pro-Street project)

Link to comment
Share on other sites

You have alot of work ahead of you. Good thing to know you have alot of the tools and equipment to get you there. Keep at it and don't loose sight of the goal. There will probably be some bad days ahead, but keep plugging away at it. Give me a call when you need an extra set of hands. Next time I will be more reliable than the last time for the unload.

 

Thanks, Brian.

Unfortunately, I lose sight of the goal when you close your garage door. ;) After you came by in your Mach 1 shortly before Charlotte, the wife told me she is really excited about this project. It's a big project, but I think it will be worth it, when it's done. I really appreciate the offer of help. Just knowing I can get a helping hand from a friend just up the road, really helps to stay motivated. Thanks!

Ron

The Rickster, a 1973 Mach 1, being restored as a tribute to my brother who passed away with COVID in July 2020.

Billy, a 1976 Ford Bronco, also needs a lot of work.

El Guapo, a 1986 F150, frame-off Resto-Mod.

Also, in the queue, a 1950 Ford F1 Panel truck and 1962 Falcon Ranchero

Link to comment
Share on other sites

  • 3 weeks later...

Well, I've got the rear end out from underneath it so I can see more of what I have going on back there. The pictures pretty much tell the tale. The floors are completely gone, with new pans laid onto of the rusted out floor with fiberglass along the edges. I've got to get the front suspension pulled, and then it will be pretty much stripped. Oh yeah, I need to remove the moonroof, too. There are a few little things, like fuel and brake lines that I won't reuse and and miscellaneous nuts, bolts, and grommets scattered around to remove. Got a quote from Don at OMS for the sheet metal so I can get that ordered in the next couple weeks or so.

 

Today, it's raining all day, so the tarp stays on the car. I decided to dig into the 351C I got for it. It's got the 2V heads and intake that I won't be using, so if someone needs a boat anchor.... Really, if someone is going to restore one of these old beasts and needs some original parts, PM me. When I pulled the valve cover this greeted me.

 

IMAG0128_zpsbxo8vxz8.jpg

 

And when I pulled the intake and valley cover, I found this.

 

IMAG0130_zpsixca6q3d.jpg

 

What is this stuff? It doesn't seem to be baked on and scrapes off easily, but it looks really bad. Can someone tell me what this is? Usually when I open one of these up on my motors, its clean, oily iron, not this stuff that looks like really soft undercoating. I was thinking of freshening this old motor, but now I am thinking teardown, clean up, and rebuild may be in order. Since I have no history on the motor, it would give me a chance to check main and rod bearings, cylinder walls, rings, etc. Opinions, anyone? (yes, I know that was asking for it ;) )

Ron

The Rickster, a 1973 Mach 1, being restored as a tribute to my brother who passed away with COVID in July 2020.

Billy, a 1976 Ford Bronco, also needs a lot of work.

El Guapo, a 1986 F150, frame-off Resto-Mod.

Also, in the queue, a 1950 Ford F1 Panel truck and 1962 Falcon Ranchero

Link to comment
Share on other sites

That "stuff" is carbonized oil deposits. Running an engine short trips, long intervals between oil changes, blow by on the valves or rings will lead to this. Sometimes a good cleaning and new valve seals takes care of this. But I would definetely check the pistons, bearings, and plan on a new oil pump and pick-up. And far as those 2V heads, those are not that bad (performance wise). Unless you plan on a high revving killer Cleveland, the 2V do make a nice street motor. Just put a nice 2V 4barrel aftermarket intake on. I have a lot of Pontiac experience and those 2V heads look a lot like the Ram Air4 Pontiac heads. Those Ram Airs would go like heck!

But then again, if rebuild is what you want, go for it and find the 4V heads and really see how this engine can roar!!! Maybe embarress a few of the big block boys out there.

Link to comment
Share on other sites

Oh man - this is looking SO familiar. ;) :D

 

When I rebuilt my engine, I stuck with the 2V heads, stock crank, and block - pretty much everything else was upgraded. According to the CamQuest utility from CompCams, I should 'expect' around 400hp, and slightly higher numbers in the torque rating. I effectively used the same formula as Doc (73vertproject), which his "Zero-to-100" videos were very convincing.

 

Considering the '71 H-Codes came with 245-ish from the factory, I'd say that's a pretty healthy upgrade... and will suit me just fine. Sure, the 4V set-up will rev higher and faster, and just goes up from there. But the best formula I've ever known is: "Speed costs money - how fast do you want to go?" ;)

 

I think the sludgey mess inside my engine was a little more rust colored than yours, though. rofl

Eric

mach1sig2.gif

Link to comment
Share on other sites

Thanks for the confirmation. I may keep the heads, although I was hoping to lighten up the front end a little. I already have the Edelbrock Performer intake and a Edelbrock carb for it. I think I will still open it up to confirm the condition, since it came from the same place as Rusty. Make sure I don't have anything more than normal wear, (like a spun bearing or worse). Always interesting (and expensive, according to the wife) starting a new project. ;)

Ron

The Rickster, a 1973 Mach 1, being restored as a tribute to my brother who passed away with COVID in July 2020.

Billy, a 1976 Ford Bronco, also needs a lot of work.

El Guapo, a 1986 F150, frame-off Resto-Mod.

Also, in the queue, a 1950 Ford F1 Panel truck and 1962 Falcon Ranchero

Link to comment
Share on other sites

You car came with a generous amount of ferrous oxide. Calling it that instead of rust sounds better :)

 

OK - "I think the sludgey mess inside my engine had a higher ferrous oxide content than yours, though." rofl

 

Mine sat dormant since sometime in 1980 (last time it had an inspection sticker on it, anyway). When I popped the oil plug, about a gallon of water came out before the sludgey mess of what barely passed for oil followed.

Eric

mach1sig2.gif

Link to comment
Share on other sites

  • 2 weeks later...

Well, Thursday morning I pulled the trigger and gave Don at OMS a call to get some replacement sheet metal. Ordered the core support, right inner fender apron (under the battery tray), full floors (both sides), trunk floor, trunk floor drop offs, tail light panel, and trunk lid. They arrived at the freight terminal not far from where I work last night, so this morning the wife and I drove down and picked them up. I'm still stripping the shell and am about ready for blasting, so now I really have my work cut out for me. Now if I could only find my spotweld cutter.

 

Time to brave the heat and humidity and get back to work.

 

Slowly, but surely.

Ron

The Rickster, a 1973 Mach 1, being restored as a tribute to my brother who passed away with COVID in July 2020.

Billy, a 1976 Ford Bronco, also needs a lot of work.

El Guapo, a 1986 F150, frame-off Resto-Mod.

Also, in the queue, a 1950 Ford F1 Panel truck and 1962 Falcon Ranchero

Link to comment
Share on other sites

Show us pics as you start to put the metal in. I am always amazed at what some of the folks have done with cars that I thought were too far gone. Persistence, patience and a lot of skill. Good luck on the project.

-john

(jbojo)

351C 4V cc heads, 10.5 : 1 CR, 290 Herbert cam, Flat top forged pistons, forged connecting rods, Atomic efi,

C6 with Gear Vendor overdrive, 3.89 Tru Trac, Hooker Super Comp with 2 1/2" Pypes Exhaust.        

 

Some Mod pictures can be seen at: [button=http://www.7173mustangs.com/forum-garage?filterxt_uid=2026]Bojo's Garage[/button]

 

 

Link to comment
Share on other sites

I forgot the pictures, but I repaired the bolt that holds the front bumper mount. That mount bolts to the frame rail in two locations. The rear one would only spin, as the bolt was rusty, and the nut was not secured inside the frame rail. There was no way to get a wrench on it, so I used a hole saw to cut a hole in the top of the rail, and a carbide burr to make it D-shaped so I could get wrench on it. Also the D-shape made it easier to get the tip of my MIG welder on the nut. I got a 1" open end wrench on the square nut, and with a little persuasion from PB blaster and the hot wrench, I was able to get the bolt and nut disengaged. I cleaned everything up and tightened the nut and bolt up in the frame and gave it some good hard tacks to secure it. Then I grabbed some 14G sheet steel, cut a patch for the hole, welded it in, and cleaned it up with the flap wheel on my angle grinder. A touch of primer to protect the raw metal and you can't hardly find it.

 

One task down, about a million more to go. I'll try to do better with the pictures.

Ron

The Rickster, a 1973 Mach 1, being restored as a tribute to my brother who passed away with COVID in July 2020.

Billy, a 1976 Ford Bronco, also needs a lot of work.

El Guapo, a 1986 F150, frame-off Resto-Mod.

Also, in the queue, a 1950 Ford F1 Panel truck and 1962 Falcon Ranchero

Link to comment
Share on other sites

  • 2 weeks later...

This weekend, I finished cleaning out the shell. Now it's ready to start blasting it, and coating the bare metal with epoxy primer.

 

IMAG0169_zpsi2ggozsa.jpg

 

IMAG0170_zpswwno53ww.jpg

 

IMAG0180_zpsv5rny6cs.jpg

 

Today, I received my spotweld cutter (Blair 11096 that Cudak888 recommended), so I can start on some the core support, take the top off the cowl so I can see if it's salvageable, or has to be replaced. Oh Yeah, we're having some fun now!!

Ron

The Rickster, a 1973 Mach 1, being restored as a tribute to my brother who passed away with COVID in July 2020.

Billy, a 1976 Ford Bronco, also needs a lot of work.

El Guapo, a 1986 F150, frame-off Resto-Mod.

Also, in the queue, a 1950 Ford F1 Panel truck and 1962 Falcon Ranchero

Link to comment
Share on other sites

  • 73MustangCoupe changed the title to The Rickster - a 73 Mach 1 work in progress

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...