Howdy im new

hello i was just refered to the site by OMS,

i have a 72 stang im the 3rd owner all texas car. im 28 its my 1st car have had it for 10 years and in the final stages of rebuilding it.

here it goes

was a 302 2v

now 351c full hydro roller with the aussi 3v style heads

holly770 vaccume 2ndarys

hooker super comps

rpm airgap intake

alumnium water pump

high volume oil pump and re-rouit kit

windage tray

msd ignition

i think thats it for engine

tranny

was a c4 now aod

was a PITA but worth it

has auto/manual valve body

shift kit

and ratchet shifter

rear end

was 8" now 9"

moser 31spline axels

detroit locker with 3.73 gears

weld on subframe connctors

traction bars by com engenering

and hd 5 leaf springs

inside

i put in that dakota digital dash i have lots of pics looks bad ass and main thing is YOU CAN SEE IT AT NIGHT!!

outside

put in full sequental led tail ligts, yes all 3 not just the outter 2 any thing else feel free to ask i look foward to helpin some of u out and reciveing the same

i put pics up there in the garage i didnt know how to do them here

::welcome:: enjoy the site. look under the more tab up top and faqs will give you a lot of site info.

::welcome::

Welcome! Sounds like you have anawesone runner. Post some pics when you get a chance.

Thanks guy!

Hi and ::welcome:: from Europe.

Hi and welcome from Australia!::welcome::

Aussie heads - good choice!

Welcome to the forums! Glad to have you aboard! Can't wait to see some photos!

::welcome::

Welcome!

Welcome to the forum.

Welcome to the club - glad you found us!

Sounds like you've got a real screamer - I'd love to see a vid of her if you have one.

Doc

Need to see some PICS!

Have you had a chance to run it? I would be interested to know the times.

Your garage looks good. Here's one of the pics so people can see it in this thread:



Doc

Welcome to the site! Sounds like you have been busy on the car!

oh my cam number is 32-541-8 thats the hyro roller cam.

think torq converter is 2200-2400

and thanks guys/gals yes look at my garage im still tryin to post some pics here in the forum

Need to see some PICS!

Have you had a chance to run it? I would be interested to know the times.

Click to expand...

no not yet im actually going to crank it for the 1st time on saturday so wish me luck i just did the base specs pluged in to that comp cam 6 deal and base will push 566hp and 556tq but till i get it broken in and on the dyno im goin with that for now


there are some pics for yall

Welcome to the site.

Nice car Mex. What are the specs on the cam?

Operating Range: 2500-6000 RPM

Duration Advertised: 290° Intake / 290° Exhaust

Duration @ .050'' Lift: 230° Intake / 230° Exhaust

Valve Lift: .578'' Intake / .578'' Exhaust

Lobe Lift: 0.34" Intake / 0.34" Exhaust

valve timeing 0.006

lobe seperation 110°

intake centerline 106°

Valve Timing @ 0.006 Lift

grind #290HR

I also have comp cam # 32-431-8 new never used its ahydro roller as well... dont need it i went wiht this cam instead


and those hooker super comps took 4 months to get and were a PITA to install fyi but it cleared by 1 inch serousley 1 inch

Is the 32-431-8 a standard or reduced base circle cam? It's the cam I would like but I need a reduced base circle to use with OE lifters, dog bones and spider.

i honestley have no idea.... but its a hydrolic roller set up cam if that helps check comp cams web site