Jump to content

Engine Rebuild and color


Recommended Posts

Started the upper build on the 302 engine where we have chosen a red, black and chrome concept.   Attached are the photos.

 

Now we've run into a question regarding rockers and pushrods.  This is what we have

 

Holley Street Avenger 570 CFM

Edelbrock Performer Manifold

Edelbrock E-Street Cylinder Heads 

      Valve Springs for Hydraulic Flat Tappet

      Port Volume: 170cc/60cc

      Valve Size: 1.90"/1.60"

      60cc Combustion Chambers

      3/8" Rocker Stud

      Max Lift - .550"

Edelbrock Performer Plus Camshaft

      Lift: .448''/.472''

      Duration @ .050: 204°/214°

      Advertised Duration: 270°/280°

      Idle-5500 RPM Range

Edelbrock Victor Alluminum Water Pump

Edelbrock Performer Link Timing Chain

 

My question is what type of rockers and shafts should we use to complete the upper build?  We are looking at the Edelbrock Red Roller Rocker  ( 3/8", 1.6 to 1 Ratio ) and  pushrods ( Length: 6.805" Dia- 5/16 ).

Will these work? 

 

thank you...

IMG-20200321-183818502.jpg

 

IMG-20200321-183846860.jpg

 

IMG-20200321-183906524.jpg

 

IMG-20200321-183926082.jpg

 

Link to comment
Share on other sites

Not my area of expertise, but I think your camshaft mfg should have that spelled out for you.  I mean if you go to Summit racing they will tell you EXACTLY what you need to match your setup.

 

Where did you get the cam.  In my opinion if you call Summit racing and ask the questions  above, I think you  will have an awesome result.

 

kcmash

Link to comment
Share on other sites

I don't know anything about Edelbrock rocker arms so, I have no input on that. Given the new non-stock parts, you will need to check valve train geometry to determine proper pushrod length. Use checking springs so the checking pushrod is not damaged. https://www.hotrod.com/articles/how-to-measure-for-correct-length-pushrods/  Chuck

Link to comment
Share on other sites

Thank you. i printed that page in a pdf format.

I'll be calling Summit tomorrow and inquire on all the input.

 

Link to comment
Share on other sites

Minimum wall thickness on the 5/16" hardened pushrods is .080. For true custom length (+ or - .002) pushrods contact Smith Brothers, Manton, or Trend. Chuck

Link to comment
Share on other sites

that is why we are being very careful to ensure all of the components are compatible and work correctly. we've researched each part so far and now we are at the rocker and rod point.

 

Link to comment
Share on other sites

That'll be a pretty engine when it's done.

 

Not sure what makes Edelbrock's rockers worth $200~$300 more than those from other USA companies, but whatever. IMO, a set of Scorpion or Crane would be hard to beat.

 

https://www.summitracing.com/parts/scc-scp1017

 

https://www.summitracing.com/parts/crn-36750-16/

 

 

I really hate that Edlebrock charges a premium for ancient tech. That cam has been around since the early 70's, the intake isn't much newer and the heads are not recommended to be used with roller cams,.....

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...