Jump to content

Recommended Posts

Has anyone replaced the weatherstrip guides on the roof seal trim?

 

I see that its riveted on.  Any recommendations for rivets?  Is there a kit somewhere?

 

Weatherstrip guide.jpg

Window Trim 1.jpg

"I drank what?" - Socrates

Link to post
Share on other sites

I have!

Mine looked terrible too.  I ordered the reproduction ones and found they were painted in  a cheap paint.  So I got some of the black tool handle dip coating stuff, thinned it and dipped them for an original look.

You must drill out the rivets and use new ones.  

The clips are actually called "Blow out Clips" and they are designed to keep the windows from popping out under certain pressure situations.

What help do you need?

kcmash

 

Link to post
Share on other sites

There have been a couple of post where these have been mentioned.  I used standard pop rivets but I cut the length of the rivet down so there was hardly any head sticking up.  The seal covers them nicely.  Some people use stainless steel rivets also.  Or you can use just the rivet without the shank and  use a punch to flatten it out.  

Kilgon

 

 

"The only dumb question is the one not asked"

Link to post
Share on other sites
Posted (edited)

I found some really small flat head brass rivets. Im going to see if they have steel too. I think they were 1/16" I don't know if thats small enough.  Im Going to keep looking.  I need to get a caliper and measure them.

Edited by jowens1126

"I drank what?" - Socrates

Link to post
Share on other sites

Mine were rusted but only on the surface. I ended up placing tape between the guide and trim. Sanded all the rust and repainted them with rust converter primer and liquid electrical tape to leave a slightly semi-flexible layer. I don't know if the liquid electrical tape was a good idea because it made it difficult to leave a smooth surface. However, they now look much better and it will require a very detailed person to notice that the surface is not smooth.

Edited by tony-muscle

20160929_171923_edit2_small.jpg

 

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump

Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes

Link to post
Share on other sites

Use a really short grip range rivet to attach the guides. The only thing below them is the door weatherstripping anyway. You'll want to use a steel rivet, as aluminum would fail over time due to the flexing these do. 

I'd highly recommend a set of the Osborn assembly manuals....

https://www.npdlink.com/search/products?search_terms=assembly%2Bmanual&top_parent=200001&year=1971

 

 

Link to post
Share on other sites

I have the osborn books on CD.  I havnt found where these are mentioned yet.  Hopefully someone thats found the nearly correct rivets will chime in.

"I drank what?" - Socrates

Link to post
Share on other sites
1 hour ago, jowens1126 said:

I have the osborn books on CD.  I havnt found where these are mentioned yet.  Hopefully someone thats found the nearly correct rivets will chime in.

 

You won't find a correct rivet in a "pop" style. Those are steel tubular (or hollow) rivets applied with a hopper-fed rivet press. You have three choices - find a company that can rivet them factory style; buy the original style rivets, make a tool and flare them at home, or get a pop rivet that's close enough. You can flare them DIY if you make a tapered punch to flare them out, then use a flat punch to roll them down to clamp the material. If you want to go that route, carefully drill the head off of the rivets and measure the diameter of the hole, then the thickness of the trim and the guide. That'll tell you what you need for a rivet. McMaster-Carr carries a small selection of this type of rivet and might have what you need. 

https://www.mcmaster.com/rivets/rivet-type~hollow/

My reference to the Osborne books was actually a response to your question about the foam ont he channel you posted in a FB group. The book calls out the size of the foam tape, you can get that from McMaster as well, or use what is preferred today, 3M strip caulk. 

https://www.autobodytoolmart.com/product/3m-strip-calk-black-08578/3m-automotive?utm_source=feed&utm_medium=free&utm_campaign=shopping&gclid=Cj0KCQjwvvj5BRDkARIsAGD9vlJBldgjmrGoCXfnEXOg3A9693137TZelNFg11kJZ-fbPK6XSpKZTfAaAosdEALw_wcB

 

 

 

Link to post
Share on other sites

WOW! mach71351c that looks great.  I have been dealing with my other cars this week.  You know how it goes, when 1 breaks they all break.  My bronco has been down for a few months and ive been dragging my feet on working on it due to working on the mustang.  Now my Durango lower ball joint decided to take a shit on me and its down till i can save up money to work on it.  So I had to get the bronco working asap.  I finally got it done last night good enough to drive, but still needs work.  Hopefully the stuff to fix it comes in today and I can wrap that up and get back on this part of the mustang project.  I only have one of the channel pieces cleaned, which took half a day.  Still have to clean up the other 3 pieces.  Then I have to rip out the weatherstripping the painter put on because he was an idiot and clean all that up before I can get the channel and drip rail on and can put the gasket back on.  Man I hate having to repeat work that should have been done right the first time.

"I drank what?" - Socrates

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...