Distributor gear roll pin. Need some expert guidance.

7173Mustangs.com

Help Support 7173Mustangs.com:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Joined
Sep 2, 2012
Messages
1,622
Reaction score
222
Location
Blue Springs, MO
My Car
1971 Mach 1, Grabber Blue w/Argent stripes. Original 2V 351C Auto, Tilt, rear defog, Black Comfortweave Interior. Under restoration. Original colors, 4V 351C, 4-Speed, Spoilers, Magnums, Ram Air. All Ford parts.
BLUF:  I sheared the dizzy gear roll pin yesterday at highway speed.  Need to know how to get her back on the road.

Details

351C 4v quench chamber , 4 speed car with 3:25 gears in the back.  Motorsport M6250-A341 cam, non roller. About 1000 miles on the engine.  Car was running great, oil pressure at the top of the gauge, temperature at the low end of normal.  Ran westbound on the interstate for about 5 miles, reached speeds of 90 mph with no problems. stopped at a shop to see if a friend was there, it idled well and had no problems getting back up onto the highway.  Cruising in traffic at about 70 MPH I suddenly lost power followed by loud explosive pops that I could feel in the floorboard.

I pushed the clutch in and saw the tach at 0 as I am losing speed in the center lane of the highway.  I try engaging the clutch to restart the engine and was greeted with more loud explosive banging.  I coasted to the shoulder of the highway and tried restarting.  It would crank but not fire.

looking under the car I found that both Turbo Mufflers on the dual exhaust were blown wide open.  Upon checking the rotor in the distributor I found the rotor could spin fairly freely, I could feel the drag of the oil pump, but it was not engaged with the cam.

Had it towed home, pulled the Dizzy and found the pin was sheared.  The gear shows no sign of damage, just a sheared pin.

how do I fix this and make it reliable?  I have a high volume oil pump which is likely the cause of the additional load on the dizzy gear according to some web research.  Of course other sources say the gear should be pressed on, which I have never seen on a Ford.  Will a higher strength roll pin solve the problem, or make me lose the oil pump drive shaft?

Note, the dizzy was a Rock Auto refurbish unit, so I got whatever gear and roll pin they put in.

kcmash 

 
I can't help it, but it reminds me of a distributor I just bought, it's supposed to be new, and I got screwed. 
A first class fiddling has been done on this igniter, really strange fiddling.

And you can see the stock distributor from my 73 Mach 1 and its original pin.

Hope nothing else has been damage in your engine.

Good luck.

IMG_20210530_175303.jpg

IMG_20210530_175312.jpg

IMG_20210530_175438.jpg

 
Go to your auto parts store and get a new roll pin, align the holes in the gear and distributor shaft, and drive in the new pin.  Rotate your engine to have the number 1 piston at TDC.  Reinstall the distributor with the rotor at the number 1 position on the distributor cap.  Start the engine, set your timing, and you should be good to go!

Get new mufflers.

 
Last edited by a moderator:
Do you by any chance have a Melling High Volume oil pump?  I ask because I broke an Accel distributor shaft in my 351C in the 70's, then went through 3 roll pins in my 460 over 10 years.  It was so bad that I started carrying a spare distributor with me. 

I read somewhere that 335 (351C, 351M, 400M) and 385 series (429,460) engines do not like the high volume oil pumps. I swapped in a stock oil pump a few years ago and have had no problem since....

 
Not only will the high volume oil pump keep breaking roll pins, it will also increase the wear rate on both the cam gear and the distributor gear. 

I haven't heard of extra strength roll pins. The only thing you might try, until you get a standard volume and pressure oil pump installed, is to install a smaller roll pin inside of the main roll pin.

 
I know that Cleveland’s are advertised to have oil restriction problems,  I will have to see what I put in there as the engine was purchased with all the parts and I assembled it nearly 10 years ago.

Looks like the remanufactured dizzy didn’t help me either.  The holes look really buggered up.

F4EFA052-3768-4C0D-ABB8-E6FE2268A1CC.jpeg

510EB5FD-A7A3-451E-B50E-D1F45805D10D.jpeg

 
Go to your auto parts store and get a new roll pin, align the holes in the gear and distributor shaft, and drive in the new pin.  Rotate your engine to have the number 1 piston at TDC.  Reinstall the distributor with the rotor at the number 1 position on the distributor cap.  Start the engine, set your timing, and you should be good to go!

Get new mufflers.
Don't forget to make sure you're on the compression stroke.  I use a piston whistle stuffed into the #1 spark plug hole.  

 
I know that Cleveland’s are advertised to have oil restriction problems,  I will have to see what I put in there as the engine was purchased with all the parts and I assembled it nearly 10 years ago.

Looks like the remanufactured dizzy didn’t help me either.  The holes look really buggered up.

View attachment 51941

View attachment 51942
It appears that that distributor shaft is toast.  Those holes should be perfectly round.  With those edges, I would worry that any new pin would be more easily broken.  If it were me, I'd replace the high volume oil pump with a standard oil pump, and also check the oil and oil filter for any metal bits that might suggest a complete rebuild is needed.  If the oil comes out clean, with a new pump and new distributor shaft (or distributor) you should be good.  Of course, that is just me, and I'm probably over cautious.  I hope there's nothing else wrong in that mill that a new dizzy can't fix.   Good luck.

 
Where does the roll pin end up when it sheers off?  If my math is correct, both ends of it have to snap off for the gear to spin freely on the shaft.  There would be at least 2 parts of metal falling down and hitting the distributor gear, possibly the cam gear, and then do they make it down into your oil pan?  Those parts of metal by themselves may be small enough to get sucked into an oil pump.  And they may get chewed up on their way down there and become even smaller and break into more than 2 pieces.

 
Well, my fears are being realized.  
 

If I am unsure of the oil pump is there any way to tell without pulling the pan?  I remember you are supposed to be able to pull a pan with the engine in the car.  Has anyone done that lately.
 

So the good news is that when the pin sheared the engine was dead and the pump was not pumping, so no metal should have been sucked into the pump.  I can pull the engine, but I really don’t want to.  If there were  a way to verify high volume versus low volume I may not need to pull the pan at all, just change the oil

I appreciate the help.

kcmash

 
So let’s go a little deeper before I have to pull the friggin engine.

 I have been running the 20w 50 high sink Valvoline Vr1 oil since new.  My oil pressure has been at the top of the range ever since I got it on the road.

Yesterday when making my highway run, I had it up to 90 mph and possibly 3500 rpm.  I went to normal residential speed and stop lights with normal temp and oil pressure.  When making my return run on the highway I was closer to 70 mph when it failed.  
 

Do we think the problem is the way the holes are drilled in the dizzy shaft, or are the holes in the dizzy shaft the result of the failure?  Also, do all dizzy gears have 2 sets of cross drilled holes, or should they only have 1?

kcmash

 
Are the 2 missing ends of the roll pin perhaps still stuck in their holes in the gear?  Maybe you got lucky and the pin snapped, but the distributor gear held onto the ends so they didn't go flying.

 
You can take the oil pan out without removing the engine. I did it not long ago. However, you need to lift the engine a couple inches. I did it by jacking on the oil pan bolts with a piece of wood. After lifting the engine use a 2x4 between engine and mount. You can also lower the sway bar for more room. Get the oil pan down and replace the pump. It is tricky to get the oil pan up and making sure it seals.

 
If the ends of the old roll pin are stuck in the gear, you're all set. Replace the pin and carry on. 

I'd consider switching to 10W30 VR1 with the high volume pump. HV pumps should only be used with appropriate racing bearing clearances, not stock. With the thick oil, HV pump and tight stock clearances, you're putting a lot of stress on the system. 

Double pinning the gear is an option, but it's treating a symptom, not the cause. Running it as is with a double pinned gear, it'll find the next weak link which will be much more expensive than a $.10 pin. 

Best solution is to drop the pan and replace the HV with a standard volume pump, but it's not needed if you run thinner oil. The only 351C I sheared a pin on was a tired 4V engine that I put an HV pump in because I had it and was running 20W50,. It broke one very cold winter morning before leaving the driveway. 

 
The hole in the distributor shaft wasn't lined up properly so they created an oblong hole allowing the gear to rotate slightly under load. This stresses the pin and will cause it to fail again. I'd get another distributor. An option is to have a COMPETENT machine shop locate the gear on the shaft properly (see Ford manual) and drill a new hole in the gear and shaft. Factory Ford distributors have the gear pressed on, many of the aftermarket one just slide on, placing more stress on the pin. All the MSD distributor I've bought have the gear pressed on. I hope you get it going again without too much drama. Chuck

 
So here are my problems.

1) Neither O Reilly or Napa have the roll pins.  They have some generic cad plated stuff but nothing strong.

2) The gear I have has 2 sets of cross drilled holes that look different sizes and it slips on.

3). I have been running the 20w 50 because that was the only weight they had on the shelf in high zinc.

The good news,  I have a spare dizzy shaft with a clean bore in it.

So I am wondering this.  With the poorly drilled holes and poorly fitting gear( non press fit) from Rock Auto combined with the 20w 50 enough to be the lethal combination.  I am unsure if my pump is high volume or not.  In other words should I do the following.

A) Rebuild the dizzy with a new shaft , gear and double wall roll pin.

B) Switch to a 10w 40 and use a zinc additive.

C) Test drive to see if that puts my oil pressure back down to the middle of the gauge range.

106A0E13-02BA-4F15-AF6C-43F4F8B05066.jpeg

 
The typical repair to any type of gear, sleeve or what have you, is to re-drill @ 90 deg. After that, a shaft of this size cannot be drilled again, it's scrap. Re-drilling is not something one can easily do at home unless you have a mill and machinist tools to set up, center drill and final drill the correct size for the roll pin. Roll pins can be bought at any bearing supply store or I have seen them at good hardware stores. Don't buy the nice shiny ones!

In your case, you'll at least need a new shaft and you'll need to check the bushing in the housing as well for correct shaft fit. Basically, you're into a distributor rebuild. If you're running a stock Autolite/Motorcraft dist. why not upgrade to a properly curved DuraSpark.

As for the oil pump, a high volume pump caused my rebuilt motor to have to be re-rebuilt. It caused the first lobes on the cam and the lifter to wear out prematurely and also took out the main bearings. Unless the build is done expressly for a H/V oil pump, don't use one. If you have any doubt, change it to a know standard oil pump which may need to be set up correctly. I only use 10W30 oil with ZDDP additive.

 
Thought about the duraspark.  What do you mean by properly curved?

if I head to pic n pull and yank a dizzy from an 80 s or 90s F150 with a v8 will that work.

otherwise I have my original dizzy from the original car with over 120k miles on it sitting in the garage.

Sounds like everyone is saying go straight for an oil pump change.

kcmash

 
Thought about the duraspark.  What do you mean by properly curved?

if I head to pic n pull and yank a dizzy from an 80 s or 90s F150 with a v8 will that work.

otherwise I have my original dizzy from the original car with over 120k miles on it sitting in the garage.

Sounds like everyone is saying go straight for an oil pump change.

kcmash
No idea about the pick and pull part if it will be close for OUR engines. As you know Cleveland's are a different beast. It likely could be reset to run at around 14 degs. initial and 20 degs. on the crank side for a total of 34 degs. mechanical advance, but I'm not familiar with DuraSparks to offer any help. There is a company, name escapes me, that will build a DuraSpark to your engine specs, not cheap, but may be worth it.

For me, the problem with using an old dist. is it was set to run at about 6 degs. initial and 30 degs crank. BUT in a pinch it might get you by for a while. Or you could carefully strip it down for parts to rebuilt the one you have, but even then, I doubt the curve will be anywhere near what we need. That was my experience. There has been much posted on the subject of re-curving a Ford distributor.

 
Back
Top