any advantage to switching 351c-4v heads

7173Mustangs.com

Help Support 7173Mustangs.com:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
it is very difficult to change pistons with the engine in the car. Just getting the oil pan off will take longer than pulling the engine.

Whether it needs bored or not depends on the condition of the cylinder walls.

 
The hand written notes on the sheet show basic SFT cam spec, CR, Ford 4V .head flow at .600, intake, carb, and timing. Internals are Scat crank and rods, Mahle pistons and rings, Clevite bearings. Scorpion roller rockers, Smith Brothers custom thick wall pushrods. If I were doing it again I'd use .5-1.0 more CR and a custom cam from Mike Jones or Brent Lykins. Chuck

The attached is for a 10:1 Boss 302 stroked to 347. There was more there (a bit rich and needed more intake valve spring pressure)but was out of dyno time.

View attachment Boss 347 Dyno Sheet.pdf

 
Wow Chuck, that’s sweet! Wish I could have done the 408 stroker, but I had to go to a .040 overbore, so I was concerned about pushing my luck with that.
I am building a 351C 408 stroker for my 70 Mach 1 M-code, The original block was already at .030 over. I would like to keep the original block, but I don't want to go to .040 for all the usual reasons. My engine builder says the cylinder walls look good and he thinks the block will clean up at .032. If it does, he will then order a set of .032 Diamond pistons. He tells me Diamond for a nominal price will allow one custom option. If the block was not original, I just assume swap it for a block with a factory bore. Anyone else over bored their block to something other than the common .005, .020, .030, .035 increments?

 
Last edited by a moderator:
I just started looking at the aussie heads, I just added a 1970 4v cast iron intake manifold and hooker 6915 (4v) headers. Would I have to swap those to 2v, too to use the aussie heads?

btw i am saving all original parts to be able to return to stock
just my 2 cents...   70 4V cost to purchase plus refurbish $$$, same for 2V aussie [I just had a set done $3,000, all good parts] 

So I would keep the 73 4V, fyi you can have them redone with 4V CC valve sizing, yes just had a guys head done.  he had a 72 & 73 CJ heads [miss match]

The 70 intake is a good one, for performance check carb to intake bores  ... 750 carb square bores are 1 11/16, 70 .  can be bored out to size of cab ...   The L looks like a square bore but is actually a spread bore ;^)

Open chambers just need more compression.   If you have newer pistons you can just order news pistons same size.  YES custom pistons will be about $1,000 - 1,200, BUT if you do the math for 70 4V CC heads ...   FYI, JE Pistons has what is 'in stock', or made to order.  So they are not completely custom, just pay a couple of dollars per change, bore, move the pin to fit rods, pressed pin, set compression etc...   the ones you'll want are the Boss 302 pop-ups   with your changes.  

Get to keep and use OEM parts too ...  with more Vroooom

pic D3-head, 70 L intake, aussie 2v cc

edited to add Boss 302 pistons in a 351C 

no talk actual things DONE

Screen Shot 2020-10-31 at 6.22.29 AM.png

Screen Shot 2020-10-31 at 6.17.12 AM.png

Screen Shot 2020-10-31 at 6.18.18 AM.png

Screen Shot 2020-10-31 at 7.02.54 AM.png

 
Last edited by a moderator:
Cleveland guys have old motors... the more you deck the heads/blocks and bore cylinders to just fit a piston will kill their longevity fast ...  adjust the piston to fit the motor you have.   jm2c

Cheeper than I thought...    retail plus YOUR changes [samples of what they have].  find one close to what you need then alter.  My JE's started with 351C flat top changed bore to 4.005, moved pin for long rods, had top cut for custom dish & set compression for a 4V '4' 61.5cc heads.  

Screen Shot 2020-11-02 at 6.15.32 AM.png

Screen Shot 2020-11-02 at 6.23.03 AM.png

 
Last edited by a moderator:
/) Another "quick" fix is to replace the timing set with one that allows you to advance the cam 4° to compensate for the retarded timing ground into the factory CJ cam. 
Rereading this can I avoid changing the timing set (and still regain the 4 degrees by simply going to a different (earlier?) cam?

 
The 72-up cam is ground with 4° of retard built in
I understand the idea of the adjustable timing set, what I am trying to understand (more for my own understanding and education than anything else) If I switch to a 1970 or 71 cam (which I infer does not have the 4 degrees of retard ground in) do I avoid having to use the variable timing chain set? And (follow-up question) if that is correct, what advantage is there to the chain solution over just changing the cam (which I expect I would do anyway to maximize power)?

 
I understand the idea of the adjustable timing set, what I am trying to understand (more for my own understanding and education than anything else) If I switch to a 1970 or 71 cam (which I infer does not have the 4 degrees of retard ground in) do I avoid having to use the variable timing chain set? And (follow-up question) if that is correct, what advantage is there to the chain solution over just changing the cam (which I expect I would do anyway to maximize power)?
The 71-74 Q-code (351CJ) cam is a long duration cam with specs of approx 205/220 duration @ .050", .480/.490 lift. The specs are identical for all three, with the '72-up cams being ground 4° retarded. Using an adjustable timing set "makes" your 73 cam into a 71 timed cam. 

The 70-71 351-4V M-code cam is much smaller cam and to my knowledge, no one manufactures that specific grind anymore, in favor of the 351CJ or an aftermarket offering.  

Yes, you could swap cams, but you're doing a lot more work for no real gain if the intention is to keep the factory 351CJ cam profile. If you're looking to swap to an aftermarket cam, then there are hundreds of options.

FWIW, 351C engines are tough on timing sets due to the heavy valvetrain. A new timing set will be needed regardless of which way you go. 

351CCamData.jpg

 
Last edited by a moderator:
Yes, you could swap cams, but you're doing a lot more work for no real gain if the intention is to keep the factory 351CJ cam profile. If you're looking to swap to an aftermarket cam, then there are hundreds of options.

FWIW, 351C engines are tough on timing sets due to the heavy valvetrain. A new timing set will be needed regardless of which way you go. 
Thank you, I plan on doing the chain anyway, just like understanding.

 

Latest posts

Back
Top