’71 Mach 1 Resto Project

7173Mustangs.com

Help Support 7173Mustangs.com:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Also, the repros don't have the seal built in. You have to use a regular twist on cap underneath
 
Also, the repros don't have the seal built in. You have to use a regular twist on cap underneath
That's true but someone told me that you can install the guts out of the factory one in to the repops, is that true?
 
Last edited:
Got up early and there wasn't anything I could do without waking the family, (attached garage) So I decided to try and restore my fuel door to see if it was salvageable. View attachment 69208View attachment 69209

It turned out pretty nice the chrome has some scratches and on the release button is pitted but overall decent condition for 50 years old.

View attachment 69210
View attachment 69211

I like before and after shots it makes me feel like I accomplished something. Once the paint cures it will be time to pack it away until the car is painted.
From an angle if you squint your eyes a bit it looks pretty good LOL

View attachment 69213View attachment 69214
Looks great! I agree it’s nice to see the before an after pics.
 
Got up early and there wasn't anything I could do without waking the family, (attached garage) So I decided to try and restore my fuel door to see if it was salvageable. View attachment 69208View attachment 69209

It turned out pretty nice the chrome has some scratches and on the release button is pitted but overall decent condition for 50 years old.

View attachment 69210
View attachment 69211

I like before and after shots it makes me feel like I accomplished something. Once the paint cures it will be time to pack it away until the car is painted.
From an angle if you squint your eyes a bit it looks pretty good LOL

View attachment 69213View attachment 69214
How did you do that ?
 
How did you do that ?
I stripped the gray paint someone previously painted it with and then cleaned and polished the chrome and then prepped for paint and masked the rivets and cap and painted with silver argent wheel paint from Eastwood. IMO, that was the closest match to the correct color I could find.
 
Last edited:
That's true but someone told me that you can install the guts out of the factory one in to the repops, is that true?
That could work, there are holes that could be used for screws/rivets
 

Attachments

  • Gas Cap.jpg
    Gas Cap.jpg
    57.1 KB · Views: 0
I got some loose ends taken care of over the weekend on the engine and in the engine compartment getting ready to drop in the engine. I have the torque converter ordered and should be here this week hopefully. I am looking forward to getting this in there.Mach 1 399.jpg
 
Last edited:
I got some loose ends taken care of over the weekend on the engine and in the engine compartment getting ready to drop in the engine. I have the torques converter ordered and should be here this week hopefully. I am looking forward to getting this in there.View attachment 69582
That engine bay is going to be nice to show off at car shows. Really looking great!
 
I got over to the body shop this morning for a little while and block sanded the doors and re-primered with the hi-build primer now one more block sanding and the doors will be ready for paint.

Mach 1 400.jpgMach 1 403.jpg

Got home this afternoon and painted the taillight bezels, they turned out okay but the bright work is pretty scratched up. I polished the lenses and the aluminum trim, but I will probably will need new lens and bezel assemblies eventually. These will be fine until I upgrade to LED panels down the road. I will need to order new seals though, the old ones were shot.

Mach 1 406.jpgMach 1 407.jpg
 
So I haven't been getting much of anything done on the car recently too busy with other things to get to body work, and the engine install is still paused waiting for the torque converter to show up. I did have a couple of hours yesterday, so I block sanded the doors but didn't have time to spray primer on them. I worked on the fenders a little they are about ready for a coat of hi-build to start the block sanding process. I also drilled out the holes in the doors for the wiring conduit and cut the holes for the speakers. This way all the cutting/drilling is done before I apply my final coat of primer. My car did not have power windows or door speakers and I am adding door speakers so I found some rubber conduits on eBay and drilled the holes for them now. This should make it so I can run my speaker wires safely when I reassemble the car.
I did both doors but only took pictures of the second door. I wish I had more time yesterday, it would have been nice if I could have gotten the doors re-primed and a coat of primer on the fenders.

Mach 1 409.jpgMach 1 410.jpgMach 1 408.jpg
 
No engine install again this weekend, still waiting on the torque converter. Supposedly has finally been shipped and supposedly will be here at the beginning of next week, we will see. Meanwhile....

View attachment 70125
Engine and engine bay look really nice! What brand of headers are they?
 
Engine and engine bay look really nice! What brand of headers are they?
Thanks! The headers are Sanderson block huggers. I got the recommendation from some people on the forum here. I was originally looking to do manifolds but wasn't having much luck finding the right ones. I didn't want long tube headers for ground clearance issues, so these seemed like the right answer for what I was trying to achieve.
 

Attachments

  • Mach 1 415.jpg
    Mach 1 415.jpg
    199.8 KB · Views: 0
I got something done today, while I'm waiting for my torque converter to show up. My shackle kits finally came off back order and showed up yesterday on UPS, so I installed my new rear leaf springs. Now the front and rear suspensions are completely done.

Mach 1 417.jpgMach 1 418.jpg
 
Last edited:
I also installed my rear valence temporarily, so that when the engine is installed I can send the car to the exhaust shop and they can line the exhaust tips up with the cutouts.

Mach 1 420.jpgMach 1 421.jpg

At lease I feel like something got done this weekend.
 
Last edited:
Still waiting for Aeromotive to get the tank in they will use to build my Stealth tank with internal fuel pump for the Sniper EFI system I plan to run on my engine. They said it should be in the next two weeks. Meanwhile, I have a big empty space in the back, just waiting for a fuel tank.

Mach 1 419 (2).jpg
 
Back
Top