I found the easiest way was to wind the door window up as it will be, close the door then get inside and move the quarter glass to match the door window. You will have the door glass to line up with and to check it all comes together. You may never get it 100% leak free with new rubbers etc...
Yes - fronts only. No rear belts as too much hassle and nobody will be in there anyway. I left the old ones there rather than dump them and a new owner may choose to re-visit this at some point. Part of the L02 requirement calls for unrestricted exit for any rear passengers so I figured that...
Does any of this help ? This plate was made to specs requested by my ADR compliance guy.
Material is 6 mm thick & plates are approx 100 mm x 75 mm. The large bolt is the seat belt one while the smaller bolt & nut secure it in place - no welding required. Position it where it needs to...
Hello from a fellow Aust owner. You'll need to post what body style it's for - Mach 1 Sportsroof I recall ? Watch for a reply from Mike Beradi
( Motorcity Mustangs ) as he has a collection of parts cars. Also Don & O M S.
Keep digging.
Does the car have air cond ? Or DID it have a/c ? I'm picking the brown wire would be connected to the compressor drive and activates the magnetic clutch when the a / c is turned on. Yes, there was a rubber grommet to secure it through the firewall. If it is ( was ) the wire to the a /c...
Hi Brendan. I'm the same poster as 188LVU on the Aust owners site.
Engine number will be on the back of the black, left hand ( drivers ) side, just below the head. This is from inside the car, not standing in front of it.
I managed to get in via the top to scrape off 3 layers of gunk, attack...
On the side, just below the cap, should be the words " cold fill " or something similar. May depend on the radiator you have if not original or good repro.
Either way, if you overfill it, the surplus will be spat out when it's at running temp. Any more than that may suggest a problem but...
So far, so good. On my earlier reply, I didn't get into the roller alignment detail. Mine were all seized up with old grease & gunk. Again, not a lot of movement so should not be a wear problem. Make sure they both move freely and the tension spring is in the right place. There will...
Not sure how you will search this, but a year or so back I recall there was an option someone found for a JEEP ! ! Others may chime in with better info but it was almost identical dimensions etc.
Keep digging.
There is very little movement at the points where the curled part of these springs contact so if they are well lubed same as the hinge pins, they should be fine. My car was missing one on the driver's side but I could not find the torsion piece on its own - ended up with a used complete hinge...
I did the same as you. Finally found the locations listed by the sticker manufacturer whom I'm sure is known to others here - Jim Somebody ? ?
Anyway: the tire spec decal goes on the passenger side door B pillar just below the lock striker ( many put them on the door itself )
The yellow...
Agree - metal plug / cap, same as the floor ones. I tried a rubber shock top cover but even with trimming the outer edges it would not fit properly & stay there. Had to re-drill one hole to line it up for the screws ( probably repro & not accurate )
And me too. Not a good pic. The recovery unit is just in the bottom right corner. Had to make a couple of brackets to keep it vertical but used existing holes in the rad support panel. Overflow tube comes through a hole down the bottom and drain sits below the stone guard underneath. Can't...
I went through the same things. West Coast Classic Cougars showed one with $38 price tag. I'm in Australia & chose to skip this. Ended up getting a 3/4" black poly irrigation fitting and doing some real backyard mods on it. Basically out of site so decided it was good enough. Keep looking.
I'm in Mackay, Qld ( sun shining & virus free ) Car is currently for sale through Aust Mustang Owners forum & Gumtree.
Local owner of a '72 Grande just had glass supplier 3 shots at getting the front screen correct.
Have fun with your project.
Have noted your number, thanks.
PKJ