Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Media
New media
New comments
Search media
Members
Registered members
Member Map
Current visitors
Tutorials
Engine, Transmission, Drive Line, Diff, etc...
Exterior, Body, Chassis & Paint
Interior Restoration
Brakes & Suspension
Electrical & Lighting
Presentation, Polish & Detailing
General Maintenance & Repair
Misc Tutorials
Forum Tutorials
7173 Wiki
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Member Map
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Doug's 73 Mach1's latest activity
Help Support 7173Mustangs.com:
Doug's 73 Mach1
replied to the thread
Quick Question about a Secondary Ground Using a new Battery Wiring Kit
.
The metal tab connects to the screw at the bottom corner of the voltage regulator as does the radio suppression choke. That connection...
May 6, 2022
Doug's 73 Mach1
replied to the thread
Someone please tell me how this goes on
.
I have the correct clip if you still need one. $25 and I can mail it to you. Doug
May 4, 2022
Doug's 73 Mach1
replied to the thread
LED light install gone wrong
.
Did you discover this bench testing or when installed in the dash? If they worked on the bench and not in the dash, it could be the...
May 4, 2022
Doug's 73 Mach1
replied to the thread
Auto to manual conversion
.
If you are changing to a 4 speed top loader with Hurst shifter, the long console used a plastic cover plate with a elongated "D" shape...
May 4, 2022
Doug's 73 Mach1
replied to the thread
28 or 31 spline
.
Another way to tell, is 28 spline axles have a deep recessed double "D" shape at the center of the hub the wheel fits over on outboard...
May 3, 2022
Doug's 73 Mach1
replied to the thread
28 or 31 spline
.
31 splines were typically used with 3.50:1 ratio rear ends and up and included a "N" case "pumpkin". Check your rear axle code on your...
May 2, 2022
Doug's 73 Mach1
posted the thread
Power seats
in
71-73 Mustang Classifieds
.
Pictured are 2, 4 way power seats removed from 71-73 Cougars. 4 way meaning they move the entire seat forward and rearward, and tilt...
May 2, 2022
Doug's 73 Mach1
replied to the thread
Help needed with more problems!!
.
I assume your car is carbureted (not converted to full injection). Could be the carb float(s) are stuck and not limiting how much fuel...
May 1, 2022
Doug's 73 Mach1
replied to the thread
NSS related question
.
I used to have a 71 with a C6. It had no wiring at the transmission, only on the shifter under the PRNDL bezel. The wiring there was...
Apr 29, 2022
Doug's 73 Mach1
replied to the thread
NSS related question
.
The neutral safety switch is built into the floor shifter wiring harness. It is the same for all Mustang automatics, C6 or otherwise.
Apr 29, 2022
Doug's 73 Mach1
replied to the thread
71/73 sports roof L.H drip rail moulding
.
I have a set and sent you a private message a few minutes ago. Check your mail box at the upper right
Apr 25, 2022
Doug's 73 Mach1
replied to the thread
71 Drivers Electric Window Bezel Clips
.
I sent you a private message a few minutes ago. Check your mail box at upper right.
Apr 25, 2022
Doug's 73 Mach1
posted the thread
Door wiring flexible rubber conduit
in
71-73 Mustang Classifieds
.
Pictured are a pair of door wiring flexible rubber conduits. These run from the front door hinge area to the "A" pillar and are used...
Apr 23, 2022
Doug's 73 Mach1
posted the thread
Sport Deck Fold Down Seat Sarts
in
71-73 Mustang Classifieds
.
Pictured is what I have, a couple of complete chrome trim sets, will need re-chroming to be show perfect. $150 complete. Partial...
Apr 23, 2022
Doug's 73 Mach1
replied to the thread
Still trying to determine my engine
.
Ford did not use the letter "I" to designate the month in date codes as it is easily confused with the number 1. So J was used for...
Apr 21, 2022
Members
Join the conversation!
Register today and take advantage of membership benefits.
It's FREE!
Participate in both public and private conversations with people that share your interest
Start new threads
See less ads
Enter your email address to join:
Thank you! Please check your email inbox to continue.
There's already a member associated with this email address. Please
log in
or
retrieve your password
.
Already a member?
Click here to log in
Don't like ads?
Did you know that registered members can turn off the ads?
Register today and take advantage of membership benefits.
Enter your email address to join:
Thank you! Please check your email inbox to continue.
There's already a member associated with this email address. Please
log in
or
retrieve your password
.
Already a member?
Click here to log in
Top