Recent content by kidwithfastback=fast

7173Mustangs.com

Help Support 7173Mustangs.com:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. K

    Howdy from Seattle

    Welcome from Seattle as well! Seeing a 71-73 mustang up here is so rare! I hope to run into ya sometime! Mines a Red and Black mach 1, feel free to pull me over:P
  2. K

    Fuel gauge went out?

    Thanks all, turned out to be a wire I hooked up for my voltmeter was tapped off the accessory wire from the ignition to the cluster. I hooked it a week or so ago.. oops, didn't notice it was drawing all the power off of the circuit. Cut the wire, and bang! Gas gauge working again.
  3. K

    Fuel gauge went out?

    I forgot to mention that I tested for power at the plug with the ignition on and it didn't show any power there. Interesting about the float, I'll check that. Sent from my SM-G900V using Tapatalk
  4. K

    Fuel gauge went out?

    I went for a drive the other day and saw that my gauge was as empty as I've ever seen it. Naturally, I figured I was just out of gas (as usual) and went to fill it up. After doing so I realized that the gauge hadn't moved at all so I went ahead with some tests. I checked the connection at the...
  5. K

    Help! Engine still wont start!

    Plus 1 to 4v. Procomp is priced so low it's hard to resist. But it is crap. Dizzy could be shorting to ground. Have you tried your old coil again? K
  6. K

    offy 360

    I had one , never ran it. It was big as a barn inside, but all my research results were similar. Too big, no bottom at all, and was regarded as the bottom pick of the the many options for the Cleveland. Sold it for 100$ on eBay. Kole
  7. K

    Name that Sound - engine noise?

    A collapsed lifter makes a heck of a racket. The long screwdriver to ear really helps isolate that kind of stuff. Good luck K
  8. K

    fmx to 4 speed swap

    Thanks Paul, most of the stuff i bought on ebay is for sale all the time for double or triple. I found if i just checked every couple days, it only took a few weeks for those kind of prices to show up. I have seen pedals, crossmembers, and z bars all sell for the same as I paid in the last...
  9. K

    What's in a name?

    kidwithfastback=fast Kole Sent from my SM-G900V using Tapatalk
  10. K

    Parts To Convert Fastback To Rear Roll Down Windows

    I did this conversion on mine. The cranks on the doors work just fine on the rear quarters. They are not to long. Never had any issues with them. reproduction cranks for sale at oreilley's. Cheap. Sent from my SM-G900V using Tapatalk
  11. K

    fmx to 4 speed swap

    What you need, .. what I paid. Where I found em Tranny. 500 Cl Bearing,bushing, seal 60 O'Reilly auto Flywheel. 90 Jegs Flywheel bolts. 15 ebay Clutch kit...
  12. K

    fmx to 4 speed swap

    Well guys, I worked a few links out of the trans linkage, fabbed/ faked in a couple bushings, in the clutch link, bolted my seat back in, screwed down a handsome rubber flex around that that classic Hurst shifter....dropped it off the stands, and went for tool around the block.. Wow!!! What a...
  13. K

    the curse of the blown transmissions strikes again

    Ha!! No sh*t!! , and I just took the cure!
  14. K

    fmx to 4 speed swap

    Extra room!?! Custom fab'd , and still barely room. Between the pitman arm, steering box, and bell housing, I'm almost surprised a four speed was an option! Big tip of the hat to Don at Ohio mustang parts, for getting me all those hard to find bits, and getting them to me quick! Did a...
  15. K

    fmx to 4 speed swap

    Ok, assembled and mounted the notorious z bar. here are all the pieces... The felt washer pops over the ball, with grease. Bedded the nylon shells with lots of grease keeper groove towards the Once in , place the clip in the two little keeper holes. I had to give it a whack with a...
Back
Top