Search results

Help Support 7173Mustangs.com:

  1. G

    Aussie Heads for 351C $300 OBO

    Selling 351C Aussie heads that I picked up. They are ready for roller rockers to be thrown on and go. Have head gasket and ARP bolts to go along with. Asking 300 OBO. Need gone ASAP Zach 619-376-9808
  2. G

    [TODAY ONLY]FMX Trans, 69 Rear End 4 Bolt, 4 Centerline 4 bolt rims $50

    Going to a dump or junkyard if no one wants. Will take any decent offer. Want gone before tomorrow because I need my truck bed.
  3. G

    [TODAY ONLY]FMX Trans, 69 Rear End 4 Bolt, 4 Centerline 4 bolt rims $50

    [TODAY ONLY]FMX Trans, 69 Rear End 4 Bolt, 4 Centerline 4 bolt rims $50 OBO Want gone! Send offers San Diego/Oceanside CA Trans shifts. Need shift bushing. I have them so they are yours. Rearend was good when I test drove the car before I pulled the engine out and bought it. Rims and a bit...
  4. G

    What did you do to your car today?

    Cleaning grim off the engine. Trying to clean it up
  5. G

    What did you do to your car today?

    Finally took the engine from the bed of my truck and put it in a room
  6. G

    What did you do to your car today?

    Thanks I will definitely do that. Some pictures.
  7. G

    What did you do to your car today?

    Need to get pictures but today I changed the front passenger side from Drum to Disk brakes. Just need a new brake line and that will be all set. I have to do the drivers later today or tomorrow. I will have my camera so will take pictures. Thanks to Mike who helped me with telling me what parts...
  8. G

    Head question. Need expert!!!! LOL

    Well I actually have a brand new set of Push rods from Comp Cam and Guide plates that are 5/16" So since you said both roller and standard may be used then I am guess that you must adjust these as they are installed on the block? Or else the rocker with slide up and down the stud? Or is there...
  9. G

    Goals for the car???

    I want my 69 to be a weekend driver and occasionally weekday driver. To have enough get up and go to out do lots of those ricer cars out there but still be a smooth ride. Hope I am on the right track
  10. G

    Head question. Need expert!!!! LOL

    Alright sweet I thought along those lines. There is any certain Rocker arm I must use? Must it be Roller rockers? Sorry new to this. Trying to learn it all. Or is it just get the studs and order Roller rockers for a 351C?
  11. G

    Head question. Need expert!!!! LOL

    These look to me to have been milled down for roller rockers. I tried the stock rockers from my 351M Heads and they dont fit and screws are to small. How do you tell if what rockers to put? And Pushrod length? Ignore the springs with spots on them. I will replace everything once I know what to get.
  12. G

    What did you do to your car today?

    Today I swapped out a 4 bolt rear end with a 8" rear end on my 69. Also cleaned off most the bolts and parts from my engine. Preping it all to be nice and clean for when engine reassembly comes.
  13. G

    Best way to remove grease and oil?

    Will give those all a go. So many bolts and nuts to degrease
  14. G

    Best way to remove grease and oil?

    Okay so I need a reliable method for removing oil and grease from parts. Mainly most of the parts can be soaked. Bolts, Rods, Rockers....you know. I have tried soaking them in dawn, Purple Power, Degreaser, Windex lol Whats a good product that will allow me to soak them for a few hours to hot...
  15. G

    $500 Bucks later

    Hey, I can tell you what I have learned. These ones I picked up are actually 2v Closed Camber heads. Bolt onto any US Cleveland block. Here's a page with a little info. http://www.ausfordparts.com/ebay/A351Cheads/ http://www.oocities.org/infieldg/v8gallery.html I have all papers proving they...
  16. G

    Met with Mike (mach71351c)

    Well, He bought my 72 Coupe from me after we agreed on a deal. Then just this weekend we tore it up. Removed the engine, trans, fenders, bumper, hood, grill and the works. Tore down my engine a little. Removed the pumps and pulleys. Had a hell of a time with a few bolts on the heads. and I...
  17. G

    $500 Bucks later

    $500 Bucks later and I am 2 Freshly built Aussie 3V heads, EdelBrock Intake, and flat tappets. Including ARP bolts and gasket set. Valve covers. All that good stuff. Post pictures soon These ones I picked up are actually 2v Closed Camber heads. Bolt onto any US Cleveland block. Here's a page...
  18. G

    7173Mustangs.com Shooters Award!

    In the Marines and we use both A4 and M4 depending on MOS
Top