Search results

Help Support 7173Mustangs.com:

  1. kiko619

    Vacuum Diagrams Restomod Edition

    Hi all! My question is directed towards how everyone else has their vacuum lines set up based on the modifications they've applied to the cars i.e. new intakes, EGR eliminated, vacuum canister eliminated, Newer distributors, the list goes on... I know of and have viewed the diagrams provided by...
  2. kiko619

    Loose Motor Mount Bolt; Mount to Block

    Hey guys! I just replaced the motor mounts on the 351C and "bolts" from were acquired from Johnsmustang. Of the 4 bolts that screw into the block. 1 bolt would not catch at all if it did. It would spin freely it is the right size because pitch and length match, however when the bolt was being...
  3. kiko619

    351C 2V Intake, Carb, Distributor, Rebuild the whole lot.

    Hi everyone, I'm currently in the midst of purchasing everything I'm going to be needing for an upgrade. The car is dead stock I figured who better to ask than those who've already gone through the headaches. This will be a build for a weekend/fun driving car and that its reliable. (not...
  4. kiko619

    351C Harmonic Balancer

    Hi guys,  I went through most of yalls posts on Harmonic balancer pics... but none have the markings I have. I’m trying to set the timing; If y’all can give me a breakdown of what ATC & BTC mean that would be really great help. Yes I know the engines had better days but the cosmetics are...
  5. kiko619

    Rear End Pinion Seal Extraction Issues

    Hi guys, So here i am trying to replace the rear end seal since it was leaking and i thought ohh... this is going to be an easy repair. I followed the typical mark ups to align everything back to normal the simple stuff... now everywhere I've seen here on "how- to extract" it is fairly straight...
  6. kiko619

    Transmission cooling line_Fittings

    Spent the weekend putting the entire drive-train back together and came to a halt. I was trying to replace the cooling lines and fitting just spun the damn line and tore it up. (Yes i used the special hex tool and still...) The whole brass fitting and the threaded coupling male from the lines...
  7. kiko619

    Possible Frame Damage?

    Hey Fam, I was putting the engine back in this weekend and was taking a look at the motor mounts staged in place and something caught my eye. If you follow the center-line eye holes of the motor mounts the're offset by almost a 1/2 inch and the drivers side is almost on top of the tie rods...
  8. kiko619

    Rust on Mating Surfaces WHAT DO I DO?

    hello everyone from the group i see that this section of our club has over 20,000 entries and clearly most of them are resolved couldn't be any happier to be a part of this fam. first the story/rant: So this VERY unfortunate event happened.... during the time i was pulling the 351C from the...
  9. kiko619

    Average cost

    Hey there fellas i have just 1 question and want 1 answer so i can average out an estimated cost of repair.. how much did it cost to have a complete driver side or passenger side floor panel replaced. i want to hear all the details yall paid for, whether or not yall took the liberty of stripping...
  10. kiko619

    howdy fellow horseback riders!

    Well hello to all my fellow 71-73 owners of all kinds of trims and modifiers!   ive been dying to get on this webstie for about 3-4 years now. everytime i tried to get registered something always happened so i gave up and continued with yahoo/ google search for possible solutions. yeah...
  11. kiko619

    i need extensive electrical assistance.

    so i was replacing the brake line, master cylinder, brake booster the works... and i had to move a lot of things under the dash and im worried i might have disconnected something that wasn't supposed to be. i had to remove the center cluster which just had the radio and the heater/ac wires...
Top