Search results

Help Support 7173Mustangs.com:

  1. M

    new member

    Welcome from Perth, Australia ::thumb:: That rear quarter looks straight as, can't wait to see her finished :) Cheers... ...Mickus
  2. M

    New Member

    Welcome from Perth, Australia ::thumb:: Good luck with the hunt, let us know when you snag one! Cheers... ...Mickus
  3. M

    Grille Support Brackets

    bump ::thumb::
  4. M

    Another new member from Australia.

    Hey Mark, the pics look awesome. What camera are you using, nice DOF! ::thumb:: Cheers... ...Mickus
  5. M

    New member from Australia

    Welcome from Perth, great to see more 7123's in Australia. I went to Mustang Day in Perth a couple of weeks ago and there would have been 100+ 64 1/2 to 70's, 1 x 73 convertible and my 71 Mach 1! Cheers... ...Mickus
  6. M

    Another new member from Australia.

    Hey Mark, Welcome from Perth. Ivy Glow, mmmmm love it! ::thumb:: ::thumb:: ::thumb:: Post some more pics when you get a chance, where are you? Cheers... ...Mickus
  7. M

    MAchi

    I used a holesaw with 1/4" arbor to make a timber template that fit snugly into the recessed cut outs under the hood then drilled a 1/4" hole from underneath through my template and through the hood. This 1/4" hole then became my guide to use a holesaw with 1/4" arbor from the top. Voila...
  8. M

    New look for the Magnum 500

    Mike, I think I can get you some of these but are 4 cowbells per rim enough? :chin: ...Mickus
  9. M

    Austin Vert's New Walk Around of Goldie.

    Looks better every time I see it, stunning bar setting vert Greg!  ::thumb:: ...Mickus
  10. M

    72 Mach 1 project

    Welcome from Perth, Australia. Gotta love green!!! ...Mickus
  11. M

    Holley vs Edelbrock carbs

    ProSystems ::thumb:: ::thumb:: ::thumb:: ...Mickus
  12. M

    New look for the Magnum 500

    Hey Mike, maybe a Flugelhorn to go with the Trombone? rofl ...Mickus
  13. M

    Help with Mach 1 purchase...

    I did some research on Joe Mayabb and uncovered this: After watching this 4.98/146 1/8 run 20 times :D  I found his email address and emailed him. Joe jnr answered my email about an hour later and told me that his dad, Joe snr, had installed the crate engine and shared some more info with me...
  14. M

    Mach 1 Mustangs are not for overparking

    Hahaha, I'm surprised that story didn't make the Wellington front page headline! :D
  15. M

    Help with Mach 1 purchase...

    Thanks Bill, yes, any personal info please PM me. I'm just after any info anyone might have about this Mach 1, if anyone is familiar with it. Was optimistically hoping someone would say "Hey Mickus, I owned that Mach 1 and it is a killer! We had to replace the rear quarter when I backed into a...
  16. M

    Help with Mach 1 purchase...

    Looking at a 2F05H that has had the 3512V replaced with a 460 built by Joe Mayabb out of Campton, Kentucky. It was imported into Australia about 4 years ago, never been registered or driven here and that's about all I know. A bit of rust in the trunk and some bog in the driver rear...
  17. M

    Just purchased 3 x Mach 1's...

    Guys, sorry for the delay. The last coupla months have flown by in the blink of an eye ::shrug:: Here's the Dropbox link for the Japanese Mach 1: Nagano Musclecar Graveyard PM me for the location if you are heading over ::thumb:: Cheers... ...Mickus
  18. M

    Ahoy Captain! I see the fins!

    Looking a little closer, I'm sure that's my dad but the woman with him looks a little shorter than mum :chin: How tall was your mum Greg? ...Mickus
  19. M

    Ahoy Captain! I see the fins!

    That looks like my parents on the balcony after a heavy night on the G&T's. I can always spot dad by his bathrobe! ...Mickus
  20. M

    Serious top end

    186 is overkill. I have a 149 here that will slip straight in! :D
Top