Search results

I agree doesnt have to be Magnum500's. But if you want aftermarket wheels go with AR Torque Thrust wheels like Frank Bullitt put on his car.

Not the factory style. But the Shelby lip spoiler always looked great on the converts!

Do not spend the bucks for Aussie heads. A while ago it was a bargain upgrade. Now it is not. And stay away from ralph the thief at powerheads. Take a look at Kaase offers. He uses CHI (also from Australia) alum heads with awesome results. There is a 3V version with matching intake that will do...

If you want the newest designed suspension system made of fordged alum you should buy a new Porsche. All new MOOG parts for our 40 yr old cars are cheap and work fine. And when yer parked at a Publix everyone will walk past the new car and stand looking at yer Mustang and smile as they remember...

the 1972 351c 2V that i bought was rated at 177HP when new. After I had the block line honed and bored .04 and had new parts (kept the crank) installed it made 378hp on a dyno and I pulled around 100lbs out from over the front wheels. new wheels are lighter with wider rubber. new brakes stop...

I believe I have seen at least 4 different vac hose diagrams for 72 351c's depending upon if it is 2v, 4v, auto, manual, ac/non-ac ....and of course if it was a california car. I also dont know if the autolite 2100 on my car even had a dist advance port. I do know that my engine had open...

they are not identical, very true. but they have 300w and bolt in real easily. unlike the radio shack 8 track and sanyo amp i wired to the Jensen 6x9's when i was 17!

73pony is right. lots of opinions. I believe GM used ported and Ford used constant and that is why aftermarket carbs have both available. I left both plugged on the Holley and used intake port because it looked original.

casmfg.com check the slidebar radio designed for our cars. I had an earlier version of one of their radios. worked fine. 300 watts total, $300 bucks. wiring matches oem plugs. easy peesy.

"forgotten generation"? he must be confusing the 71-73 with the mustang II gia pos.

dont forget that after you finally finish that 450+HP work of art and drop it in the car...you will find that the trans will never hold up...and the factory brakes are not up to the job anymore...or the springs/shocks for that matter...etc. So the answer to yer question is "around $30k over a...

I had a disagreement about this issue in the past. I will tell you what I found. The gas cap on my 72 has a rubber gasket and a small hole in the center of the inside of the cap. When the cap was tested by the DMV inspector I was told the cap doesnt hold a vacuum. When the DMV checked on their...

quarter windows?

i believe you will need different mounts. These cars came with choice of 4 blocks and used different mounts for the converts as well.

MY swap from oem 2V to 4V involved the factory intake replaced with an Edelbrock intake, both of which use a vac connection tapped in the forward area of the intake. That was how Ford designed it and always worked just fine with my new Holley and factory dist.

71-73's were available with a 302 so obviously you can make the swap. But unless you have some financial incentive to do the swap why would you want to remove the best designed engine ford ever produced and install the older, less efficient agricultural lump?

He didnt say not to use water, he said not to use a hose....do not spray pressured water on the car because the seals are not tight. A bucket and a sponge and elbo grease is always an option.

where would you find a 1975-1980 granada/versailles/monarch 4 wheel disc proportioning valve? they made hundreds of thousands of them. cant be too tough, no?

yeah but he wants the idiot light to work. here is a brass aftermarket for 4 wheel discs that will activate the idiot light. http://www.ebay.com/itm/disc-disc-PROPORTIONING-VALVE-COMBINATION-VALVE-w-Fittings-for-four-wheel-disc-/230775945538?vxp=mtr&hash=item35bb517942 But a granada...

How about the block/proportioning valve out of a 75-80 granada/versailles? They came with 4 wheel disc brake setup.