Search results

I finally broke down and bought a new driver side window regulator for my 71 Mach.  I've never been happy with the one that's in there and how sloppy it is, and how it doesn't come up totally level at the front.  So the questions I have are: Can I replace the regulator without removing the...

I have a 71 351C original to the car.  When I rebuilt it a few years ago, the 2v heads were milled along with the block a total of .029 to both raise compression and to true the block face.  I added an Edelbrock 4v manifold and Holley 4v carb and an improved Comp cam at the same time, and am...

When it came in, was the short actuating arm attached to the output shaft of the motor?  If so, it could be attached incorrectly, and so the wipers would be 180 degrees out of phase.  If you decide to pull the motor and change the arm to check it, DO NOT attach the arm to the transmission before...

The real value of VR1 is for the zinc.  As much as it costs for an engine rebuild, it's all I use.

Get hold of kid's modeling clay, and put a lump of it on top of the tallest point under the hood.  Next, close the hood gently, open it again, and measure the height of the squashed clay.  Same sort of thing you do when checking valve to piston clearances.

The block off plates were actually more for aesthetics than functionality (not leaving a big ugly hole).  Even a functional ram air system (I have one) will allow water in under normal conditions, but not in sufficient quantity to cause a problem.

It was the name of Henry Ford's mansion.

I was going thru my old posts today, and realized I hadn't gotten around to posting pictures of my completed Fairlane.  It took me about 5 years to do.  So, here goes.  This is a stock paint job, interior, etc.  The chrome on the engine is stock as well, because it has the GT package.

The tach on my 71 Mach has suddenly stopped working.  It worked fine uo until a couple days ago.   I had to get the car hauled to a tranny shop (they had to pull the tranny and replace the flex plate).   On the way home, I noticed it wasn't working.  I suppose there's something the shop could...

Hood to cowl seal.

Yup.  Where I come from (northern Montana, where -35 isn't unusual in the winter), they're called a "Montana Thermostat"... :D

It's a Comp Xtreme Energy XE256H cam. The specs are at: http://www.compcams.com/Company/CC/cam-specs/Details.aspx?csid=846&sb=2 As for adjusting the timing up, is 10 degrees good or would you recommend more?

I would but have no way of getting it up into the air to do the examination. I don't know there's enough room to get a magnet past the fkywheel.

Faulty soleniod.

In all my time with cars, I've never seen this happen.  Started my 71 Mach (351C) yesterday, and heard a funky clinking noise for a second as it fired.  Shut it down after warming it up for a bit, then tried to restart it.  Nothing.  Start just spun at full speed but didn't engage the flywheel...

I've owned my 71 Mach with a 351C for 10 years now.   For all that  time, I've never experienced a more cold blooded car.  When cold, it idles ok, but put it in gear and it stalls (same thing coming to a stop at a corner).  I have to be quick on the throttle to get it going - kinda hard on the...

OK, so I finally got the parts in the garage sorted out enough that I could get the car in. So, here are some pics. Keep in mind, I said the body was pristine, not the paint. There's obviously cleanup to do, and the passenger side door is in the trunk, awaiting getting its rust hold repaired...

Hope to get some this weekend. It't been colder than h**l here (-9 a couple days ago). Just too cold to uncover it & shoot. Be in the 50's this weekend, so hopefully I can get some pics.

$3k, clean title. Let the hating begin... But now you know why I couldn't pass it up! :D

Got the Fairlane home yesterday, and had a chance to go through it thoroughly today. Man, I cannot believe this is an unrestored, 46 year old car! The thing is just so pristine. I found 1 minor dent on the RR quarter above the wheel, a crease towards the bottom of the LR quarter behind the...