Search results

My father has a 1962 Galaxie 500 4 door in good shape down in Tennessee. The motor is disassembled, but block is still in the car. Has original A/C unit still. No break through rust, and has original interior. He has purchased a few new parts including tires. Has a complete 352 to go with it...

I tried searching for someone who has posted a beginning to end bumper resto for a 73 front bumper and couldn't find much. The one Mustang&Fords article link is not complete whenever I search for it. I have a couple small tears on the bottom of course, need to know how to repair and glue down...

Does anybody know which starter a 1973 Mach 1 351 Cleveland with 4 speed would need? I do know it's a 164 tooth flywheel. Thanks!!

I just wanted to get a post out with pics of all 3 of my babies. One lives in Minnesota with me (Boss 351 clone), and 2 are stored at my fathers in Tennessee. (73 Mach 1's) The Boss clone has a 351 CC head engine, RPM Air-Gap and custom Carb. The Brown one is a mostly stock Q code with A/C, and...

Hey gents! Looking for a decent rear valance for a 73 if anybody has one. PM me if so. Thanks!

I have 2 351 Cleveland standard bore blocks, one is a 1970 (DOAE-L), and a 1972 (D2ae-CA). They are not magna-fluxed or tested. Grease was smeared in the bores years ago. And I have no desire to clean them for inspection. Looking for $250 ea. Or if someone on the forum wants them both I will...

As the subject says, I'm looking for a usable set of steel rims with mustang (Ford Motor Company) hubcaps and beauty rings. I'm ok with a 14 inch set as well. Thanks!!

Finally finished 73 aluminum rims!! Machinist had to spend 8 hours repairing the center cap screw holes, lots of elbow grease with polish, some touch up paint for black lines and new valve stems. Can't wait to get them back on the car!!

Does anybody have any tips or tricks for cleaning/restoring the aluminum rims. I have a set on one of my 73's that need some TLC. Just wondering what others have done to freshen them up?

I have inherited a set of 8 pistons and connecting rods for a 351C. I was looking through them yesterday and found that I have 2 number 8 connecting rods. Not sure how this happened, but here is my question. If I am having them all reconditioned can I run one of them in the missing number 7...

I know I saw on the forum once how to rebuild the ram air vacuum actuators, Can anybody help me find this info? Thanks!!

So I got a 4 bolt, 4bbl Cleveland from my father that was a running engine when he took it out of the car. It should be a 73 engine because that is what his car is and it had 73 motor mounts on it so I'm guessing it's the small valve OC heads. He said it ran strong and didn't smoke when he took...

Looking for a pair of the Steel 351C "powered by ford" valve covers for a H.O. rebuild. Shipping to MN. Please let me know. Thanks!

Does anybody have a good method for repairing cracks in the full consoles? I also have to build up one of the mounting screw holes. Any input would be greatly appreciated!!

Time is my worst enemy, never enough of it. That being said, I would like to start stripping body panels for repaint, BUT, I can not do everything in a weekend or steadily at all. If I strip my panels to bare metal what can I spray on them that will seal them for long term storage. I would also...

I have a 3 spoke ginger steering wheel. The center pad is lackluster and I want to replace it. The re-pops only come in black. Should I dye or paint the re-pop? Which color? They have a medium and dark ginger soft plastics paint at NPD. Which color is the right one for a ginger interior? Any...

Does anybody know where I can get a replacement piece for this part? See pic. Rubber insulator for interior door handle actuator. Thanks!!

I have been looking at different grilles, some claim to be NOS, others are Goodmark, (lots of $$$) and average catalog ones, but I have heard some horror stories about the cheap catalog ones. Anybody want to share their experiences with a new 73 grille? Thanks!!

Good Morning Gents and Ladies. I have yet another question. As I am sure you can tell I am gathering parts for another repair/resto. Last night I had my wife order a master cylinder and she says there are 2 available. One has a 1" piston bore and both brake line holes are 3/16" I believe. The...

Does anybody know which bushings I need to buy for rebuilding our idler arms? Any tips on doing so? I do own a hydraulic press. Thanks!!