Search results

For those who have not seen my dashboard swap, I successfully swapped my spare dash but for some reason my fuel gauge now peges our all the wY . I checked my grounds to body and they are good. This was not an issue 2 or. 3 weeks ago before the swap. Thanks Tom

While putting my dash back together, my heater/AC control fell off the table. Below is the disk that came off. Can I repair this and how? Thank you in advance. Tom

Does anyone have a pic of a corectly installed below pic? Thanks in advance. Tom

I have a spare dash but around the glove box are holes for a bezel. That’s the best way that I can describe it. I used to see these for sale and apparently my Google-Fu is not up to standards anymore. Does anyone have a source for me to buy one? Thanks. Tom

Guys, this is whooping my butt, I had the short console around my FMX auto shifter and recently picked up a long center console from a member here. When going to install, it will not line up or fit properly under my center stack bezel. If I leave it about an inch from the rear of the shifter...

Anyone know the best brand and shade for the black that goes around the 71-2 tail light lenses? Thanks in advance. Tom

I thought that I had this fixed a few months ago because the intermittent clunk when turning hard left to the stop and then back right about a quarter of a turn disappeared after torquing the ball joints and down to specs. Now all of a sudden a couple days ago, I noticed the clunk was back. It...

It’s been awhile since I posted anything other than asking for assistance so I thought that I would post this. I found the last bit of rust on my 73 Mach 1, the trunk lid. And since it had factory drilled holes for the rear spoiler, I took some pics and measurements. After I made the...

I had a link save previously for the ignition switch adjustment and cannot find it, can someone post the instructions for the ignition switch adjustment please? I installed a new switch about a year or so ago and it was always a little "off" and one of the comments that I received was to keep...

I am contemplating reinstalling my original 2 Spoke steering wheel but will need all of the parts that go on it. I have put together a list from NPD below but something tells me there is something missing or I have things on my list that I do not need. Can anyone confirm that the below is all I...

I have rebuilt my front end, new upper control arms, lower control arms, both upper and lower control arms included ball joints, inner and outer tie rods, new conversion from drum brakes to disk brakes kit ( Willwood kit), front strut rod bushings, stabilizer bar bushings. The only original...

I wanted to say that Bob at RCC Innovations did a great job and extremely quick work and return of my non-functioning tach. Great throughout the process with shipping/repairing/upgrading it to a modern 3-wire. Also great at assisting me with the new connections to get it working. Bob, the tach...

I have a 351c 2v with Performer 2750 and Summit Carb 750 CFM. Stage 3 cam and recent full rebuild by myself. The plugs show it to running rich. My idle likes about 1000 rpms and my static timing is 13-14 degrees btc. I have vacuum at around 17 and does not bounce around. The currents jets in...

Can anyone tell me what goes here and a part name/number/source? I am pretty sure it is the crankcase breather filter but there are 2 holes not one. Thanks in advance. Tom

I have a 73 Mach 1with a 351 Cleveland and have successfully installed a ram air with the Petronix Billet Distributor installed. I have a Summit 750 CFM carb installed with the edelbrock 2750 performer intake. As I already suspected and this forum stated fitment would be a problem since the...

So my 73 Mach 1 351 Cleveland has been starting and running pretty good, the last couple days I even added the ram air ( another thread to be started because I have a petronix billet distributor) and it was running good tonight. I adjusted the initial timing to 13 and it was starting good and...

I remember seeing a post about Ram Air and Pertronix Billet distributors but cannot find it now. I have a 351 Cleveland with Edelbrock Performer Intake and Summit 750 carb with a 1 inch spacer, as well as the Pertronix II Billet distributor and want to install Ram Air this fall. I have heard...

Good evening everyone, I recently purchased the Pertronix Ignitor II for my 351 Cleveland 2V, model number 91281 from Summit. The description and "check fit" option says that it works for a 1971-73 Mustang 351 Cleveland. But when I install it, the cap wobbles and is not tight. Because of this...

Pretty sure that Kevin's (Turtle5353) car is in this video, anyone else see their car in this video? Tom

Does anyone have a diagram for a FMX automatic transmission shifter linkage and can post a pic here? My FMX is out of a 1972 Mustang (as far as I know) and when following the linkage directions that I found on here, it says "loosen linkage nut under the car, place the shifter in the Drive...