Search results

you may see this in another forum, as i wanted to ensure i reached the vert people also. I am in the process of putting on my new vert top with a 'glass' rear window. In doing the process, the inner pads were installed and removed several times during the fitting which is normal and they are...

I am in the process of putting on my new vert top with a 'glass' rear window. In doing the process, the inner pads were installed and removed several times during the fitting which is normal and they are all set. We are now at the point where the first installment of the rear window is being...

Does anyone have any photos of how the gas tank seal to the filler pipe is suppose to be properly seated? The extended portion of the seal which the pipe goes through has several waves in it and I can either extend it up the pipe as shown below where it lies flat, or double over the extreme end...

I need a new NASA hood.  I would prefer an OEM in good shape, but if need be I'll take an aftermarket.  I'm up in the New England area. There are a few websites to get a new hood (not OEM) but i don't know which one would have a quality part. NPD Goodmark Carid etc, etc. Can anyone point...

Below are two photographs of the passenger's door electrical window pigtail.  When I took the panel off, I found the yellow wire in the photo taped to the back of the pigtail it was not connected.  The yellow wire is however a part of the harness and is molded in.  I had problems with 'all' of...

When the engine was installed by the machine shop, two Prothane Motor mounts (6-503) were installed to replace the original worn ones from Ford.  According to the machine shop, the Prothane mounts have a slightly lower profile than the Ford originals due to the polyurethane material.  As a...

We are having a hard time finding the correct power steering hose (pressure) for our 73 Vert.  I've ordered about 3 to 4 from Mustang websites but they all comeback wrong.  The machine shop where the engine presently is located also cannot find the correct one as the original hose is worn and...

My 302 was quipped with dummy lights in the instrument cluster when it was built.  I recently acquired the original three gauge cluster for the center console with the wiring harness that has two display lights. My question is whether or not I can tap directly into the wiring from the sensors...

I am looking for a chromed Harmonic Balancer for a 302. searching Summit Racing, this is the only one i found.  Not sure if this is correct. Can anyone steer me in the correct direction and is the PowerForce a good quality replacement? Thanks, Dan

Can anyone tell me where I can get a set of new weatherstrips for the bottom of the doors on a 73 Vert? The ones on the door 'do not' extend up to the window seals.  I've checked numerous places but they all include the seals as a portion of the weatherstrip.  The photo below shows the end of...

After having installed new brake lines and connected them to the distribution block, ( D2ZA 2B328 AA X ) I finally isolated where a single leak was coming from and it happens to be the brake warning switch.  It is a good leak and I am positive fluid is coming out of this particular port. All...

Has anyone seen one of these and where can it be decoded?  It was discovered in the rear seat as we took off the fabric.  Its been cleaned up as shown below thanks, dan

The C4 was rebuilt back in 2018 and the proper fluid level had been added. In order to do some additional maintenance, we then removed the tail shaft and the transmission pan about 1 year later.  We were not able to capture all of the leaking transmission fluid to measure, so we do not have any...

Started the upper build on the 302 engine where we have chosen a red, black and chrome concept.   Attached are the photos. Now we've run into a question regarding rockers and pushrods.  This is what we have Holley Street Avenger 570 CFM Edelbrock Performer Manifold Edelbrock E-Street...

Can anyone offer a good manufacture for a vinyl top with a glass rear window from my 73 Vert? I have been looking at either KEE or EZon.  If someone knows another one, I'd consider that also. We plan on installing the top ourselves. Dan

the 73 Vert did not come with a center console light.  We picked up an original on ebay and installed it.  I now need the wiring lead from the main harness to the light pigtail. Does anyone know where i can pick this up so we can get power up to the center light? Thanks

There was a thread that dated back to 2012 regarding this issue, but i did not really answer my question regarding the trunk light. There are two types of lights i can find for sale, but not sure which one is correct and fits the mounting area in the trunk lid. Neither bracket appears to be...

Shown below is my 28 spline rear axle from an 8 inch casing. One of the parts required for the rebuild is the rear wheel bearing retainer (NPD # 4020-1). This retainer with the small hollow at the bottom is also shown in the parts manual for Ford with what appears to be a gasket (parts 4234...

Ford just rolled out its new 2021 Mustang. Its electric and now a 4-door. No longer will they be making the two door power house. What is the world coming too.... Hold onto your horse or they'll probably come and try and take that away too... Dan

Below are two photos; the back of the power booster and the other the firewall where it mounts. in the power booster photo, an arrow has been inserted to point out a valley which is present on both sides of the unit.  The firewall mounting area however is flat with no protruding part to fill...