Search results

I replaced the floors and seat platforms on my 1971 Mustang convertible and had a question about the stud that the seats attach to on the seat platform (see pic below). Does anyone know how this stud gets attached? Is it attached before the seat platform is welded in place or after? Do they sell...

I got this bracket in a box full of parts for my 71 Mustang convertible bit I'm not sure what it is and where it goes. Can anyone help me? Thanks.

I need an OEM passenger side fender for my 71 Mustang. Looking for one that is rust free and not dinged or dented. Would be great if we could ship it using Fastenal or another shipper like that. I am in north Georgia and can pick it up if not too far away. Thanks.

I bought the one piece Dynacorn Mach 1/coupe floorpan for my convertible and it came with seat platforms. I checked around on the forum and also on Google but could not find an answer for how high a convertible seat platform is. Can anyone tell me? I'm not sure if I need to cut these platforms...

I replaced the turn signal canceling cam on my 1971 mustang. After I got everything re-wired and back in place, I noticed a small, thin metal bar about an inch long laying on my workbench. It's at the bottom of the picture and is circled in red. Can anyone tell me if this may be part of the...

This topic may have been covered before but I couldn't find it anywhere on the site. I am wondering if coupe upholstery be used on a convertible? I have read the front seats should be fine but what about the rear seat? Will coupe upholstery just look crappy in a convertible or can something be...

I searched the forum, the internet and my assembly manuals but could not find out where the pot metal headlight trim ring below mounts. It's probably called something else but not sure what that is. Can someone tell me where these rings would mount? They were in a box of parts when I got my...

I need a set of brackets that attaches to the headlight assembly (see pic below circled in red) but I'm not sure what they're called. Mine were disassembled when I bought my Mustang and I can't find them. Looking for a straight, as rust free as possible set. Thanks.

I am looking to buy an original, tested and working vacuum actuator and arm. See pic below for the specific actuator and arm I need. Mine won't hold vacuum. Thanks. George

Can you tell me how I can remove the A/C thermostat control wire probe that is inserted into the A/C evaporator core? I tried pulling it out by hand but it didn't budge so I let it be until I asked you guys. Is there a trick to removing the probe after it's been inside the evaporator after 52...

I am restoring my A/C heater system in my 1971 convertible and I'm not sure what attaches the bracket on the floor vent to the fan box (see pic below - circled in red). When I took my unit out of my car there was no screw or clip connecting them together. It was just flapping in the breeze. Thanks.

My 1971 Mustang convertible came with Trim code CW which is white, knit vinyl comfortweave material. I have seen a striped, black and white pattern on the center section for the CW trim code (see pic below from Stocktrader). My convertible still has the original upholstery and the center section...

I need an A/C idler pulley and mounting bracket for my 1971 Mustang with a 351-4V. I see WCCC sells a mounting bracket here: https://secure.cougarpartscatalog.com/d1az-2888-a.html but is says the bracket was used after 4/27/1971. My car was built in February 1971 so I'm not sure if I can use the...

I am attempting to install the center dash panel in my 1971 Mustang but I'm having a hard time figuring out where it screws on. I see where the four screw go that attach the radio and A/C - heater panel but I also see two screw holes near the top by the center A/C vent (see pic below - they are...

I am looking to buy a pair of rust free door jamb panels. Thia would be the panel attached to the rear quarter where the striker plate and lower vent are located. Let me know if you have a set and how much you're asking. Thanks.

The body shop is tearing out my poorly patched, rusted floors and told me I need to replace the lower seat platform that mounts under the floor. The pic I posted below if for a 65 - 68. Is there one reproduced for the 71 - 73 Mustang convertibles? If not, would a 65 - 68 work with some mods? Thanks

I soaked my very rusty emergency brake and got it clean. When I flipped it over to rinse it off and dry it, a piece fell out and I'm not sure where it goes. I also noticed the handle and arm don't spring back to position like they used to since this piece fell out. I have attached some pictures...

My 71 convertible is completely disassembled and I am working on restoring the dash while the metal work is getting done. As a result, I can't try the convertible top switch to see if it works. I am worried it may have issues because when I move the convertible top switch lever one way, it...

The 71 Mustang brochure mentions that any Mustang ordered with the Decor Group option (like my convertible) got deluxe black instrument panel appliques. So what is the difference between the standard interior and deluxe interior driver side and passenger side panels? Also, if you order the...

I am looking to buy the following parts for my 1971 Mustang convertible with a 351 4V and auto: 1. D0OF-12127-G distributor (would be great if the date was before 2/25/71) 2. D1OF-FA or D1OF-AAA carb 3. Set of 1971 deluxe convertible seat belts (black if possible) 4. Under hood light 5. Front...