Search results

7173Mustangs.com

Help Support 7173Mustangs.com:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. M

    Drip Rail Molding Seal

    I have a 72 Mustang and I'm looking for the part number for the seal that goes between the drip rail and the second molding. Can't see to fibd it listed. Was going to just use 3m Sealer but that's a little messy. Thanks,
  2. M

    Vehicles For Sale Project 1972 Fastback and Parts Car $8,000

    Ok so I have a friend who has a 72 Fastback on rotisserie (comes with it) and a 71 Fastback parts car to go with it. All of it is going for $8k. You would have to work with Dave directly, but this is a great deal for someone who wants to finish this project. All the sheet metal has been done...
  3. M

    72 Mustang for Sale

    Ok so I have a friend who has a 72 Fastback on rotisserie (come with it) and a 71 Fastback parts car to go with it. All of it is going for $8k. You would have to work Dave directly, but this is a great deal for someone who wants to finish this project. All the sheet metal has been done...
  4. M

    Gauge Cluster Pinout on Circuit Panel

    I looked all over for this and only found circuit coding and I really needed something that break it all out pin by pin. Now this is a standard cluster no bells and whistles, so if someone what's to expand on this your welcome. I'm doing an aftermarket harness (Painless) and things like this...
  5. M

    Heater Hose Outlet on 351C

    Hello Good Members, I have a new puzzle again. The hot water hose inlet on the top of my 351C is not the threaded type it seems to be more a pressure fit type. I can only seem to find the threaded type can someone point me to where I can get one that doesn't have threads to fit? Thanks,
  6. M

    Drive Identification Assist

    Yes I was a bonehead for not marking my driveshaft when I took it out. I have a solid end, and another end has a thin neck. Which end is ID'd as the yoke end? Thanks,
  7. M

    New Quarter Panel question

    I had to replace the lower portion of both quarter panels. The question is right where the rear bumper meets the quarters there a two holes. Is there something that goes there or should I fill them?
  8. M

    Power Steering Pump Swap

    Hello Members, Can I swap out this power steering pump: With this one without replacing the steering box: Thanks
  9. M

    Electric Water Pump and Alt Brackets

    Afternoon Members, I have a 72 Fastback project and that includes a 351CJ. The engine was professionally rebuilt and I put an electric water pump from Holley, well because I got it for a deal. Now the problem is "where can I buy an alternator and power steering pump brackets. The original...
  10. M

    Crankshaft Puller Fitment

    Hi Members, I've added an electric water pump to my 351CJ, I've been trying to locate a crank shift pulley that will work with an Alternator and Power Steering pump. Now there seems to be tons of 351W crank shift pulley in the configuration I need. So the question is "Will a 351W crank shift...
  11. M

    Wheel Bearing Seal- What?

    Ok I have looked everywhere and I just can't seem to find a seal for the inter bearings on the front brake rotor. Would I be correct that one is not used on the rotor bearings? How is the bearing and grease held in? Thanks
  12. M

    Replace the Strut Rod or not

    I know metal gets less reliable over time. The car is a 72 with 53k original miles on it. Should I replace these or clean up and reuse?
  13. M

    Rear Drum Brake Hose Size

    Thanks in advance for feedback on this. When I try and install the rear center Drum Brake Hose that is spec at 11.77" but it is extended to over the max maximum length when the axle is fully extended on a jacks. I'm afraid that one bump when it fully extends the hose will cause damage. I...
  14. M

    How to Identify a 9in Diff

    Is there a way to tell if you have a 9in rear-end without opening the diff? Thanks,
  15. M

    Door Removal/Install Hack

    How any times have we found ourselves struggling to get our doors on and off the car with out yelling to the wife to come give you a hand, or calling up a friend to come by and hold the door while you get it removed or installed. Well no more guys. Here is a door removal/install hack that I've...
  16. M

    351CJ Intake Manifold "Where are you"?

    Ok, so I've first started calling around to Edelbrock, Holley and others looking for an intake for a 351CJ heads. Now remember these ports are large (2.65/1.88). My engine builder told me to find the intake that matches the Flopro gasket 1228. Well that was the Edelbrock 2665, but when it...
  17. M

    Side pipe Ground Effects

    Anyone know where I can buy these side skirts?
  18. M

    Starter with Solenoid for 351C

    I'd like to put a starter in that has a built in starter solenoid and do away with the one that hangs off the engine bay fender. Anyone done this before and if so what model starter would work? Thanks,
  19. M

    Trunk replacement without cutting it in pieces

    So I was watching a few online videos showing how to replace a trunk panel. They recommend cutting it on the ends over the frame support rail so you have a solid weld area. Here's the thing I'm not only replacing my trunk panel and the two drop down panels, but also the quarter panel and outer...
  20. M

    Keeping My Mustang Honest

    I don't know why anyone covers the complete underside of a car with that Rubberized Coating. In most cases they do it to hide things. And in my case that was also true. Sold on solid floors but when the carpet is pulled back and the undercoating removed, not so solid anymore. This is how you...
Back
Top