Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Media
New media
New comments
Search media
Members
Registered members
Member Map
Current visitors
Tutorials
Engine, Transmission, Drive Line, Diff, etc...
Exterior, Body, Chassis & Paint
Interior Restoration
Brakes & Suspension
Electrical & Lighting
Presentation, Polish & Detailing
General Maintenance & Repair
Misc Tutorials
Forum Tutorials
7173 Wiki
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Tech Forums
Electrical, Lighting & Electronics
Air conditioning vacuum canister plumbing
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support 7173Mustangs.com:
Message
<blockquote data-quote="Animal Lawyer" data-source="post: 379495" data-attributes="member: 7401"><p>Ok so after replacing the hoses and valves etc on the engine side my a/c was not getting the car cold. I went to test the vacuum control system (as set forth in the service manual, and after running the car and turning it to acc the vacuum gauge went immediately to zero. When I got the car the canister was not connected and I attached the 2 hoses in what seemed the correct configuration (the larger engine vacuum line to the larger port and the smaller line (going to the ac control panel to the smaller port. However, after removing the old canister I realized none of the vacuum lines were original and that may not be correct.</p><p></p><p>1. Does anyone know which port the engine vacuum is supposed to go to (in other words, did I screw it up?) and 2. it is my understanding there is supposed to be a one way valve built into the canister, is there and if so, which port is it on and in which direction does it work (I am assuming it is on the engine vacuum side and prevents air from re-entering the canister when the vacuum on the line drops (thus keeping the canister "charged" to provide vacuum to the control even when the engine is not producing vacuum)</p><p></p><p>I'm hoping to troubleshoot the vacuum part of the system myself rather than paying my mechanic the hours to do it (I believe I am capable of setting the controls as instructed by the service manual, turning the car from run to acc and reading the gauge) </p><p></p><p>Finally, on the right side of the control panel (behind the bezel) there are 2 electrical connectors, which color wires go to each position (as I moved the bezel to snake wires for the stereo install the 2 connectors came loose, I blindly reconnected them and the heater/defrost functions all seem to work well (at least when the car is idling and vacuum is high) but I want to assure myself that I did not cause the a/c issues by doing something stupid (like reversing the 2 plugs).</p><p></p><p>Thanks in advance. </p><p></p><p>Rich</p></blockquote><p></p>
[QUOTE="Animal Lawyer, post: 379495, member: 7401"] Ok so after replacing the hoses and valves etc on the engine side my a/c was not getting the car cold. I went to test the vacuum control system (as set forth in the service manual, and after running the car and turning it to acc the vacuum gauge went immediately to zero. When I got the car the canister was not connected and I attached the 2 hoses in what seemed the correct configuration (the larger engine vacuum line to the larger port and the smaller line (going to the ac control panel to the smaller port. However, after removing the old canister I realized none of the vacuum lines were original and that may not be correct. 1. Does anyone know which port the engine vacuum is supposed to go to (in other words, did I screw it up?) and 2. it is my understanding there is supposed to be a one way valve built into the canister, is there and if so, which port is it on and in which direction does it work (I am assuming it is on the engine vacuum side and prevents air from re-entering the canister when the vacuum on the line drops (thus keeping the canister "charged" to provide vacuum to the control even when the engine is not producing vacuum) I'm hoping to troubleshoot the vacuum part of the system myself rather than paying my mechanic the hours to do it (I believe I am capable of setting the controls as instructed by the service manual, turning the car from run to acc and reading the gauge) Finally, on the right side of the control panel (behind the bezel) there are 2 electrical connectors, which color wires go to each position (as I moved the bezel to snake wires for the stereo install the 2 connectors came loose, I blindly reconnected them and the heater/defrost functions all seem to work well (at least when the car is idling and vacuum is high) but I want to assure myself that I did not cause the a/c issues by doing something stupid (like reversing the 2 plugs). Thanks in advance. Rich [/QUOTE]
Insert quotes…
Verification
Post reply
Tech Forums
Electrical, Lighting & Electronics
Air conditioning vacuum canister plumbing
Join the conversation!
Register today and take advantage of membership benefits.
It's FREE!
Participate in both public and private conversations with people that share your interest
Start new threads
See less ads
Enter your email address to join:
Thank you! Please check your email inbox to continue.
There's already a member associated with this email address. Please
log in
or
retrieve your password
.
Already a member?
Click here to log in
Don't like ads?
Did you know that registered members can turn off the ads?
Register today and take advantage of membership benefits.
Enter your email address to join:
Thank you! Please check your email inbox to continue.
There's already a member associated with this email address. Please
log in
or
retrieve your password
.
Already a member?
Click here to log in
Top