Malwood under dash clutch kit

7173Mustangs.com

Help Support 7173Mustangs.com:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I installed the one from American Powertrain. The master cylinder push rod angle is terrible and I have spent too much time dialing it in. I am ordering the Malwood pedal tomorrow.
 
I installed the one from American Powertrain. The master cylinder push rod angle is terrible and I have spent too much time dialing it in. I am ordering the Malwood pedal tomorrow.
I have the malwood and have been very pleased with results. Angle is spot on.
 
I have one. Product is qualit. I had issues as I was converting my auto pedal box to a manual pedal box. The Scott Drake bearing kit did not fit right so I had to modify the Drake part.

I ended up trimming some of my pedal box to make sure it cleared the malwood cylinder. Unsure if my pedal support was wonky or just a faulty installer valve
 

Attachments

  • B5A758C2-4E8E-47DE-ACD7-8F7B1FE4A77B.jpeg
    B5A758C2-4E8E-47DE-ACD7-8F7B1FE4A77B.jpeg
    1.8 MB · Views: 23
  • 95393614-E4F6-423E-9092-24F25C086CB9.jpeg
    95393614-E4F6-423E-9092-24F25C086CB9.jpeg
    3.6 MB · Views: 22
  • C8CFEF22-44D0-4611-A693-2139A468A7ED.jpeg
    C8CFEF22-44D0-4611-A693-2139A468A7ED.jpeg
    2.1 MB · Views: 22
  • 22DE17B1-EC7D-421B-B0F4-C98061F1A81E.jpeg
    22DE17B1-EC7D-421B-B0F4-C98061F1A81E.jpeg
    1.9 MB · Views: 22
  • 17434A09-24B5-4EDC-9590-6D78C36F9C3F.jpeg
    17434A09-24B5-4EDC-9590-6D78C36F9C3F.jpeg
    1.6 MB · Views: 21
  • 74430BAC-E6D2-461E-9D59-CC906B8D00F0.jpeg
    74430BAC-E6D2-461E-9D59-CC906B8D00F0.jpeg
    3 MB · Views: 20
  • AFB81E6F-4C1E-43C3-8A37-F1A4D1035093.jpeg
    AFB81E6F-4C1E-43C3-8A37-F1A4D1035093.jpeg
    1.8 MB · Views: 21
  • 4F6B7A18-6BAC-49C7-AEE8-5EA2CFDD3390.jpeg
    4F6B7A18-6BAC-49C7-AEE8-5EA2CFDD3390.jpeg
    1.6 MB · Views: 23
It will be a while. Working on fixing the poor decisions in the 90’s. Stock vs how much I cut out. Now adding back in.

getting the body and electrical working before I assemble the engine and buy the transmission

still trying to decide on blown 357c, NA 408c, Coyote or new Godzilla
 

Attachments

  • 81DB9E19-5011-44ED-A66C-6C7C58C3B2FB.jpeg
    81DB9E19-5011-44ED-A66C-6C7C58C3B2FB.jpeg
    3.1 MB · Views: 6
  • 5B7595C3-BAA5-4F3F-981E-7D179C9FA1F2.jpeg
    5B7595C3-BAA5-4F3F-981E-7D179C9FA1F2.jpeg
    2.6 MB · Views: 6
  • 9AF200B4-6151-42FE-9855-CD6E34395F9A.jpeg
    9AF200B4-6151-42FE-9855-CD6E34395F9A.jpeg
    3.9 MB · Views: 6
  • 854A8B65-7121-481B-B58F-3C6AABC4C706.jpeg
    854A8B65-7121-481B-B58F-3C6AABC4C706.jpeg
    3.2 MB · Views: 6
  • E323A097-CD6E-434E-9E7B-87ADFB1439AE.jpeg
    E323A097-CD6E-434E-9E7B-87ADFB1439AE.jpeg
    27.2 KB · Views: 6
I installed one on mine with their TB. I had to shave a little of my factory pedal assy for smooth actuation. Other than that, I have about 1500 miles on the setup and she's solid. Their customer service has called me back on a Sunday for what it's worth.
 

Attachments

  • 20200216_153250.jpg
    20200216_153250.jpg
    1.4 MB · Views: 8
  • 20200216_153203.jpg
    20200216_153203.jpg
    3.8 MB · Views: 7
  • 20200321_193457.jpg
    20200321_193457.jpg
    3.7 MB · Views: 7
  • 20200322_132035.jpg
    20200322_132035.jpg
    1.2 MB · Views: 8
  • 20200322_112904.jpg
    20200322_112904.jpg
    3.5 MB · Views: 9
  • 20200322_135210.jpg
    20200322_135210.jpg
    4 MB · Views: 9
How is the Malwood working now? The one I got that mounts on the firewall was a PITA to install and very difficult to adjust the linkage. We obviously got something wrong and it failed at about 4,000 miles. We are considering getting the Malwood if it will work with the installed throw out. If not probably do the MDL mechanical which, alas, means pulling the transmission. Argh.
 
It is an absolute pain in the $ss to install with the pedal box in the car. It was designed to be installed on the workbench from what I can tell. I have swapped from the American powertrain assembly after the second master cylinder failure. It is in the car but I have not driven it yet as I am doing some other mods that have taken more time than I care to think about. But it is a very good quality part.
 
All of my install issues were the Scott Drake needle bearing pedal kit.

I pulled the pedal box out as I converted mine from an auto pedal box.

I am getting close to adding fluid and bleeding it.

then I will see if I need a pedal stop.
 
How are you guys routing the hydraulic lines for the malwood kit?

I'm getting ready to order the moderndriveline package. They are currently defaulting to the malwood clutch master cylinder. And your choice of a hydraulic throwout bearing or the traditional fork with an external slave cylinder pushing the fork back. I am leaning towards the second option, the external slave cylinder, just for the ease of adjustments and repairs down the road.

So I will somehow need to get the hydraulic line from the driver's floorboard out and then around to the driver's side of the transmission.

The two obvious choices I see are either straight through the firewall and then snake around to the side of the transmission, or poking the line right through the transmission tunnel where it will come out closer to the transmission.

Also, how are you mounting the fluid reservoir? Does the malwood kit take care of that or do you need to get creative and find your own place for it?
 
Sorry I can't help with a lot of that as I'm running a Wilwood on the other side of the firewall. FWIW - It does seem like going out the firewall would be pretty straight forward and tidy.

I'm not sure if there's a disadvantage to the way it works, but I'd personally prefer to have an external slave for serviceability as you mentioned. I've had to pull my tranny twice to service mine (Hydramax) within a few hundred miles after it was installed. It's been great since, but sure would have been nice to be able to just slide under there and fix this issue in an afternoon.
 

Latest posts

Back
Top