I don’t think my abilities would go as far as pulling anything else out of there. I did pull out the outer bearing and it looks fine, but now I cannot get it to back in...lol. I probably need to add some oil to it and the shaft to help it slide in, since I wiped the one it had on it when I...
My mustang has pretty much sat in the garage ever since I bought it about 3 years ago waiting for a transmission swap. I would run it for 15 min twice a week. One day I noticed a small puddle of rear end oil.
Now, with all the time spent at home I decided I'd give it a shot at replacing the...
So I ended up swapping the bellhousing and range selector arm/shifter linkage from my original transmission to the replacement. The transmissions were swapped this past weekend. (I ended up hiring a mobile mechanic and tagged along to learn) I took the car out for a short test drive and it seems...
I kind of thought that might the case since most trucks have a column shifter. I know they are different on the C4 and C6, but didn’t really investigate much about the differences in the FMX. I read in another forum that the tail shaft and housings are of different length and that both would...
I found a guy selling an FMX. He said it was rebuilt, he bought a new converter, installed it on a 60s/70struck, but never ran it. Then decided to go with an AOD instead. So he removed it and stored it. He added some tranny fluid to the converter and transmission.
When comparing it to my...
I have been considering dropping the transmission and give it a shot at the rebuild using the Bad Shoe Productions video. I have never removed a transmission before either, but have seen a few videos on what the process is and found this post as well...
I found those videos from Bad Shoe Productions while looking up FMX tutorials on youtube. All I found was a video of a guy with a French accent disassembling the transmission. I have zero experience with transmissions so I felt like I was not getting much out of it (especially since my...
@mudbilly - don't plan on using it as a daily driver so probably less than 200 miles a month I would say.
@mbrew2 - sounds as if you were describing my car. It is also a 73 convertible. I have come to believe that the FMX fits the use I have planned for this car and do not really need to go...
I am in a bit of a dilemma and wanted to get your suggestions. The FMX on my 73 with a 351C was suffering from “morning sickness”, but the last time I took it for a drive around the block it was slipping and I even thought I might not make it back home. In the end I did make it home but have...
Well I feel stupid! I went back and checked the firing order and I had mixed up the wires on one side of the motor. I fixed that now and have not gotten the backfire (thanks for the correction) at startup, but I still get it when I floor it while driving. The car seems like its going to die when...
I removed the wires and cap from the distributor. I was going to try to remove it, but could not remove the bolt with the tools I had so I left it in there; and completed the intake swap with the distributor in place.
I installed the plate to "convert" the intake to a dual plane intake. Other...
I recently swapped my stock 2 bbl intake and carb for a Weiand X-cellerator I bought used and a new Edelbrock 650 cfm Thunder series carb. My car is a stock 73 351C 2v with a duraspark ignition (bought it like that from the PO) and an FMX. I am having a couple of issues after completing the...
Thanks for the suggestions. I had no idea this transmission required this much attention to detail. I usually take the car out for a drive on the weekends, so it most likely had been sitting for about 1 week. The car was at normal operating temperature when I checked the fluid level as I had...
This is my first time owning an FMX car. I have had a 302 with C4 and 351W with toploader in my previous 2 Mustangs. I have a couple of questions, but will address one issue at a time.
When I pull the car out of the garage and into the driveway I've experienced the following symptom. The...