Search results

for sale 351C-4V edelbrock intake manifold #2665 aluminum never used brand new still in orig box $200 free shipping in continental US. email for pics

two 351c-4V heads closed quench chamber heads bare no valves no springs need rebuild , free shipping continental US only, $250 send email for pics and to send request for payment on paypal if you decide to buy

never used milodon 351C timing chain and gear set brand new. 15006 premium roller timing chain set. $52.00 and the ride is free. SOLD!

Looks like a Windsor crank so beware of interchange problems. I had a 393C stroker w/ Windsor crank and had some problems. If you use a Cleveland timing gear set you also need a special spacer and watch the contact w/ the keyway. I found the keyway only contacted the crank gear a very small...

for sale: 1971 boss 351 stock intake manifold. D1ZX 9425 CA aluminum $600.00 obo buyer pays shipping from 93631

for sale a 31 spline traction lok differential pumpkin 3.5 for $500.00 obo and buyer pays shipping from 93631. pics available

planning to install pertronix dist but have to install 12v relay and so would like feedback on how it goes in since my voltage reg plug has no 'I' wire

The voltage reg plug on my 71 mach 351 4V has: F - orange blue S - green red A - 2 yellow wires I - no wire Is this normal to have no wire to terminal ‘I’. question came up when I wanted to install a pertronix 12v relay and had to put a diode on the wire to terminal ‘I’ but had...

I have a set of 4V heads I will sell for $100. not much demand now. The iron intakes are not in demand . I will sell you two for $50. carbs also not much demand cause after market much better. I checked out aussie 2v closed chamber heads a while back and could not find a piston that would make...

A bad seal on intake manifold gasket can cause intake port to suck oil into cylinders. You did not say if you use the valley pan and gasket. These come in a set and the gasket is paper thin to account for the thickness of the valley pan. If you use the pan you must use the paper thin gasket it...

I assume the engine was balanced. the best balance is with the flywheel and damper to be used on the engine and every thing is spun together w/ the crank. some shops use a mock up of the damper and flywheel when they are not supplied w/ the rotating assembly then if the actual damper and...

accepting reasonable offer on 1971 standard black front seat . buyer pays shipping.

check out Coast High Performance ...they make a rotating assembly for 351C which ends up being a 357 at 9.5-10.2 CR with small chamber heads and dished pistons.

I use contact cement to glue the cork gasket to the oil pan and the rubber semicircles to the block. This keeps the gasket from moving . Also allow easier removal cause when gasket glued to pan it comes off in one piece still attached to pan. I coat the cork with some grease before installation...

I need a set of OEM 351C-2V heads. please include the casting number and price. open chamber is ok.

I found the metal to metal seal technique required excessive pressure tightening on the exhaust stud nut so I purchased some bulk pieces of exhaust gasket from summit and cut out a doughnut shaped piece of gasket and placed it over the end of the exh manifold and tightened the pipe over the...

8 stock 351C con rods DOAE-A and attached pistons 30 over. offers?

one standard black seat for 71. offers?

after breaking two pittman arm pullers from harbor freight I had to buy a stronger tool which I have included the name and bought from summitt which did the job. OTC Tools 8149 - OTC Universal Pitman Arm Pullers. did not want to use a torch which would probably damage the seals in the steering...

while rebuilding a 71 mach ,,I took apart a steering column someone had beat on the center shaft w/ a BFH to remove the wheel. the column center shaft is in two parts and work like a telescope with one half slightly smaller and inside the other. comparing to another undamaged column the column...