Search results

SOLD SOLD SOLD ---- Lot of 5, 1972-1973 Ford Mustang Grande Deluxe Stainless Steel Hubcaps. 14" hubcaps will also fit other 14" Ford wheels including the 1971 Mustang Grande. These are a good to best driver set with minimal small dings on only a couple of the caps, one has a slight dent, one...

Does anyone know the difference between a PS pump spacer for AC vs. car w/o AC? I see a lot of venders have pump spacers for cars W/O AC?Unfortunately, I need a spacer for my air conditioned 73 convertible. Thanks all for your input. Doug in Indy

Greetings. Going through my pile of spare parts I found an original battery heat shield for a Boss 351/429 performance Mustang. Anyone here know what it might be worth? I know these shields got tossed in the trash during battery changes.. making them rare. Thanks. Doug in Indy

I have a 73 Conv. with orig. Motorcraft 12127 D3ZF distributor. Do you know where I can find a rebuild kit? I have new points, cond. & rotor.. but it's gonna need springs and gasket etc. Thanks Doug in Indy

Hi. Need some help. My 73 conv. 351C turns over strong but wont start. Batt. tested good... tested 2 coils, both just shy of 9000 on secondary coil... getting a spark from jumper wire attached to neg. lead on coil to ground.. but seeing no spark from plug attached to center coil wire during this...

Greetings Need help finding proper vacuum hose route on my 71 conv. 302 2v auto, no A/C... Although I've had the car many years, I went to check it for first Spring drive and notice that one of the vacuum lines had come loose from the dual advance on the distributor... now I can't seem to...

HELP! My 71 Mach 1 with C6 automatic has developed an issue of not going into 1st gear... it starts out sluggish in 2nd gear.. goes to 3rd and  seems to randomly drop back to 2nd.. but not to 1st as the car slows down. I tried manually selecting 1st gear with selector... nothing happens... I...

Hey all... My 71 conv with 302 2v  has developed a leak at the brass tranny line adapter... I see replacement elbos for the C4 but will they also fit the C6? also.. should I be able to remedy the leak be simply replacing the "O" ring on the threads? As always, thanks for your help! Doug in Indy

Hey all... My 71 conv with 302 2v  has developed a leak at the brass tranny line adapter... I see replacement elbos for the C4 but will they also fit the C6? also.. should I be able to remedy the leak be simply replacing the "O" ring on the threads? As always, thanks for your help! Doug in Indy

Preparing for weekend World of Wheels show with our James Bond tribute '71 Mach 1

007 free upload without registration Diamonds Are Forever tribute

Hi all I am looking for a kick down rod for my 71 Mach 1 with 4bbl Holley carb and C6 trans. I bought a used one from a local vendor but it did not fit... it was then I realized I may have bought an FMX version... not C6? I would be willing to trade the FMX for a C6 kick down rod. Thanks...

Hey all My 71 Mach 1 starts up and runs great but wont shut off when I turn the key to the off position. Here is what I tried: Switched starter solenoid with a new one, same problem. Switched again with a known working Autolite solenoid.. same problem. Removed the ignition starter on top of...

Greetings Working on my 1971 Mach 1 with 351C M Code C6 AT... Could not get the car to start.. after jumping the safety switch wire the car would turn over.. so I'm assuming the NSS unit went bad. I see repops for sale for the C4's but not the C6? are they interchangeable? Is it possible my...

Anyone know what color the coil spring stripe marks would be for a 71 Mach 1 with 351C,4v PS no AC ?

MOTOR WON'T CRANK OVER UPDATE Huh Thanks all for your input.. this is still a frustrating issue. To date, I've put in a new Motorcraft battery, it's reading 12.56 volts. I replaced the starter relay with new one (not repo concourse) I bought an auto circuit tester and tested the wire coming...

Hi guys Unfortunately, my 302 2v 71 convertible wont turn over. Had it running fine earlier this Spring. then let sit for two weeks.. went out to start it and nothing. So far Ive replaced the battery, put in a new starter solinoid.. but all it does is make a single "click" sound. Battery is...

Hi guys Having issues with trunk lid alignment... the lines on the lid look perfect on both sides and across the back... the lower left corner is sitting nice and flush with the quarter extension.. the issue is that the upper left corner is sitting an 1/8" high and the lower right corner is...

Hi all. Restoring a 1971 Mach1 "M" code.. or so I thought! Was stripping the motor to repaint and found the casting numbers under the block. D2AE-CA and 2 J 9... unfortunately, I thinks this must mean my original motor was replace with a 1972 motor? Also, the motor did have a 4v cast iron...

Hi all. Restoring a "rough but usable" floor console.. does anyone have/make/sell the push button lever for the lid latch? Thanks! Doug in Indy