Search results

I would like to get a longer shifter to raise up the handle and move it back closer to me. Doing this as i need to recurve anyway to clear the radio i want to put in my "dash". My neck is jacked so I need a larger area for car play and backup camera. Are there any bolt on options or do I need...

I have a gas tank that a shop put in my car 20 years ago. It has never had gas in it. They welded in a return in a fuel return bung. When I pressure tested the tank, there is a small pinhole leak at the bung. I tried to repair it, but it is past my capabilities of myself and the welder. I am...

My passenger window is hard to roll down. Up is fine. Anyone have any suggestions. Both sides were fully cleaned and greased when I swapped them into the different doors TIA

I bought a new ignition cylinder and door lock set so I can have matching keys since my original door locks were lost. Old key cylinder returns after start, but the new cylinder doesn’t. Any suggestions? Thx in advance.

Anyone seen a kit or pre welded set of jacking rails for our cars like pictured? TIA.

Got this in trade years ago Was told it was a Lincoln Versailles rear but definitely questioning that. The axle plates don’t seem to match up with the pic I have. Flange to flange is 60.25” It came with a center section I am currently running in my original existing 9” housing. Anyone have...

New Russell 693080 71-73 mustang DOT brake lines. Looking for $80 shipped via USPS priority mail to lower 48 or wherever if you want to pay the difference. Stupid me I bought this twice so it was extra for my car.

Offered this here on threads. Putting an official post. I bought this in 2001 and a shop installed it, but never has seen fluid. I decided to install a top loader I also had. the converter is a billet 10” designed to take the torque of my supercharged 351c. the trans has a modified 1st gear...

Shop installed these 20yrs ago, but the project stalled and I went another direction. Shop layed them in the compartment and then lowered the engine in against my suggestion so they got scratched a bit. The engine was never started with these installed. asking $600 plus actual shipping...

Edit. All parts spoken for. Ok this is my second set of parts. Free to pickup from Plano, TX Alternatively I will ship for the cost of shipping. Here we go!!!!!! Reman starter. Free to pick up or $25 to ship Coupe rear quarter extensions. Free to pickup or $25 to ship Auto brake pedal...

*EDIT* I had to send the stuff away. It started to be an issue at the house. I have some parts leftover from my build. They are free, but I won’t ship so if you are near Dallas, Tx……. 73 passenger fender fairly good condition 72 passenger fender minor damage at extension…no trim Coupe...

Complete rear out of a 73 base 302 coupe.  Open diff.  Highway gears.  Working when pulled years ago.  It was stood up on both tires at one point or another and the gear oil filled the drums.  So plan on some maintenance. it is in Richardson, Texas.  (Suburb of Dallas) free to good home.  I...

So pondering........ My car has gone through a rough life.  18 year old self went through a parking lot at way greater than parking lot speed and folded the car at the passenger window (Mach 1 fastback). I drove it until the engine died and parked it in the garage. About 10 yrs passed and I...

Hello I have a 351c that had and FMX behind it. The shop installed a C6, but put a manual block plate in. Anyone have a block plate for a 351c and a C6 before I go eBay? PS. If you have the inspection plate, too that would be great. Thanks, RCA

Looks like this posted today. I am thinking of contacting the person tomorrow Anybody have any red flags? https://dallas.craigslist.org/dal/pts/5743669332.html Thanks

Long shot, but I think it is time for the truck to go. It is a sonic blue 2001 lighting. It was color changed from black before I bought it. Engine and trans are built. Full SS long tube cat exhaust. 3.4L whipple Aluminum radiator with electric fans Aluminum heat exchanger Single pass...

I think I want to run AN line for the transmission cooler to help with clearance to the floorboard. Was thinking of using a fitting then be able to screw a pressure rated hose onto the fitting. Anyone have one? Thanks, RCA

Shop that was doing the work put in a motor plate for a standard trans. I am looking for the automatic plate and access panel that goes between the trans (c6) and the engine (351c) If anyone has one or can point me to the correct part that would be most excellent. Thanks, RCA

Me....just past mid 40's and still have my High School car. It has not been on the road since 1987 when the engine went south. I tried to do a total rebuild in 1990, but the body shop went out of business and I had to go get the car parts that remained by flashlight. Tried again about 1998...