Search results

My steering has no feel, it's too "loose". I don't mean mechanically loose , I mean it has no feel, no feedback. It's like there's no weight on the front tires. I've "lived" with this since I rebuilt the front end. I think I remember hearing that there was a check valve or something that could...

Found that DUPLICOLOR BFM0041 from AUTOZONE will work, I'll let you know.....

Just shook it prior to and during the entire "FREEBIRD" song, and the same thing. The ball was free when I first tried it, and now after the "FREEBIRD" shake, it's still not spraying a color. Thank's for the reply though.....

Tearing out what little hair I have left out trying to find SEM 15855 paint to finish my "A" pillar covers, 1972 Fastback. I ordered SEM "15993", because that's what the old can was labeled. When I got it, the spray that came out was a clear spray. Rechecked the old can, and found a sticker on...

Looking for someone to talk me out of trying to replace my oil pan because it's dented, because "if it ain't broke, don't fix it." I've read where it's possible to do this by raising the engine, but that the oil pump pickup needs removal, other people say it's easier to just remove the engine...

I have the 2 pieces of rear seat trim (?) that go across the top where the package tray is, and also the 2 side pieces. Is there some kind of small cover to hide the place where the 2 at the package tray come together? I have put the pieces in place, and the parting surface where the two meet (...

Check Scottie Strickland, great guy to deal with. He's in North Carolina..

Finally got a pair of fastback "A" pillar covers. Do i need to remove the dash pad to install them?

Found it, works like a charm............Thanks

Thanks, I'll check it out today...........

I don't think I have a TPS. Would going to the windshield wiper motor power wire be ok? The wire through the boot idea is good too, except I'm not a good solderer, LOL! I know my limits............

Wiring the electric choke to my Motor craft 2100. I WAS going to go to the "S" terminal on the alternator like I did on my '66, but the lug is a push on type with a covered connector, so that won't work, and I don't really want to start splicing any wires into the charging system, ( followed...

Thanks, that's probably the direction I'll go too...........

4 blade fan (17") $20 C-4 rear trans mount $20 289-302 exhaust manifolds with the choke heat tube $100 2 outer tie rod ends (ES387L) $25 289-302 dip stick and tube $10

Just received the 2 top and 2 side trim pieces and trying to find out what color they should be. Do the 2 that go across the top in front of the package tray get painted to match the tray or seats? Also the filler trim on each side of the seat back, should it match the seats?

I have a Motor craft 2100 carb that I just received an electric choke for, but it only has one very short wire to connect it to a 12 volt source. On my '66 289 I hooked it to the "s" terminal on the alternator, but this wire is way too short to reach it.  I am guessing I could just make my own...

Just reinstalled my rebuilt 2100 carb and installed a new WIX screw in filter. I seem to have a very slight seep from the parting surfaces where it screws in. I know that there should be NO gas leaking, but before I over tighten and strip something out, I am wondering if there is a gasket or...

Thanks for your help! The voltage checks were within limits so I removed the small ground wire from inside the distributor and cleaned both ends with emery cloth as well as the attach areas inside the distributor, also at this time the "old" condenser was installed. I turned the key and it...

How do I check for voltage at the points?, What should I see there?

Ok, I think I still have the old condenser somewhere, I'll give that a shot......thanks