Search results

anyone running a high flow water pump and did it help cool the engine? drop the the temp versus a standard water pump

been having problems with my power steering. after 1 1/2 year of dealing with all the work involved and expense, i had enough. going to convert to manual steering. i found the correct crank and water pump pulleys, i need a manual steering box and pitman arm, the center link are the same, from...

power steering pump makes a loud squeal starting at 2000 rpm. pump and steering box was rebuilt at a rebuilder with lifetime warranty. the first rebuild they installed a fast ratio in box, think it was 12.5 to 1. everything was good until box started to leak, sent it back and was fixed and...

anyone know where you can buy the reservoir can? you can buy the reservoir with the pump, but cannot find them separate. CVF racing sells a reservoir, but want to keep stock.

 has anyone had a set of M/T valve covers and had to remove the drippers so they would clear roller rockers on a 351c

does anyone know if ford would have installed a 180 or 192 thermostat in the 351c

fan on car now is a 5 blade 17 inch. some traffic lights in town are very long, temp gauge goes up some sitting soo long and with summer here it does not help. thinking about a flex a lite 6 blade or 7 blade. kind of like to stay with mechanical fan, has correct 351c thermostat, new 3 core...

does anyone know if they make upper radiator mounts? i found the lower mounts but not the uppers

looking for a factory am /fm radio to fit in my 73. what other years and models will fit

this might help someone on here, i ask this before and got no response. wanted to install only the ram air plenum because engine 408c has rpm air gap intake and a spacer under carb and MSD dist. 1/2 inch clearance from top of wingnut to bottom of hood. installed the plenum and the ford racing 13...

wanting to cut 1/4 to 1/3 of coil off spring, noticed that the last 1 1/2 of spring is straight. there is a tab on the spring perch, where the end of the coil stops against it. question is cutting end of coil off, removes that straight section off the coil. will it still sit on spring perch...

what type of coil spring compressor are you guys using? one I bought one from advance auto is too wide and will not fit inside spring, without having to modify it. have factory service manuals and see how it works with no problems. are you guys removing the plate [ inside the fender } that...

have a set of M/T valve covers, what grommets are you guys using for the pvc. was going to use original twist on oil fill cap, will not fit, would have to trim ears of cap to fit, and then would not know if it would lock in place, till I tried it. hate to do that and ruin cap if it does not work.

PA PERFORMANCE 3G upgrade. factory alternator wire harness removed. installed 4 GA wire from alternator to starter solenoid, or does it need to go where the factory installed it? from what I have found this is called the starter distribution block { could be called something else }. or do I...

want to change stock alternator to a 1 wire or 3G setup. which is the easiest. car has factory amp gauge, does it need to changed so it can read volts?

nose of car sits a little higher with new engine, aluminum heads and intake, AC removed [ did not work]. if I cut the coils, for every 1/2 coil, how much will it reduce the height? or should I contact eaton spring? like the current ride of car, do not want it to ride harder.

might have to replace a bad roller cam lifter. do I have to pull head to get lifter out, because of being longer.

does a voltage regulator use the body as a source of ground? someone has over tightened the mounting screws, cannot get it tight like it needs to be.

new engine 408c, 13.5 to 14 of vacuum at the manifold and at the vacuum modulator. transmission is C-6 from performance automatic. when you drive it easy, it upshifts early and seems to slip before it go in drive. if you stop and take off and give it more gas [ drive it harder ] it shifts fine...

after you installed speakers in the rear deck of your fastback, what did you do with the spare tire? have 2 1/2 inches gap from top of tire to the bottom of the rear deck. speaker measures 2 1/2 inch from mounting flange to the bottom of magnet, these are 4 by 10 speakers that fit the factory...