INPete

7173 Mustang Supporter Member

Active member From Greenwood, IN

Joined: Jan 15, 2023

Last seen: Wednesday at 1:15 PM

Latest activity Postings About

- I
  
  INPete replied to the thread 351c motor frame mounts.
  
  I'll keep those in mind. I have found a set of 71-72 hardtop brackets that I'm working a deal on at the moment.
  
  Apr 28, 2023
- I
  
  INPete replied to the thread 351c motor frame mounts.
  
  Thanks for the heads up on the NPD adjustable mounts and the simple remedy. A quick question on the frame stands, would it also be ok...
  
  Apr 27, 2023
- I
  
  INPete replied to the thread 351c motor frame mounts.
  
  I'm also in this same dilemma with my 73 vert. I've started a new engine build and would like to upgrade the engine mounts, but can't...
  
  Apr 27, 2023
- I
  
  INPete replied to the thread Unobtanium… Show those hard to find parts in your stash….
  
  Seen this on eBay as I was searching for an Avocado center dash for my dash gauge install...
  
  Apr 14, 2023
- I
  
  INPete replied to the thread Ram air hood.
  
  I did call Mustangs of Chicago and they did confirm they have a NOS hood. A bit more than I'd like to spend. But, thanks for the lead...
  
  Apr 12, 2023
- I
  
  INPete replied to the thread Need confirmation of correct flexplate to order for FMX.
  
  After calling a few manufacturers, it was still unclear and confusing. However, Performance Automatics did tell me their flexplate will...
  
  Apr 12, 2023
- I
  
  INPete replied to the thread VIN Check.
  
  Not sure what the police will need on a VIN check. Here in Indiana, as long as the VIN on the dash is visible, that is all they've ever...
  
  Apr 11, 2023
- I
  
  INPete posted the thread Need confirmation of correct flexplate to order for FMX in Engine, Transmission, Drive Line, Etc.
  
  Sometimes I get brain overload from too much conflicting "information" when searching online. So I'll ask the question here, seems like...
  
  Apr 10, 2023
- I
  
  INPete replied to the thread Ram air hood.
  
  I appreciate the info. It is difficult to decide without seeing them in person.
  
  Apr 8, 2023
- I
  
  INPete posted the thread Ram air hood in Exterior, Body, Chassis & Paint.
  
  Looking to replace my standard hood with a NACA (ram air). Can't seem to find a good used local factory Ford hood. Any suggestions on...
  
  Apr 5, 2023
- I
  
  INPete replied to the thread Factory looking aftermarket radio.
  
  I recently installed the USA-740 and fits perfectly into my 73 vert. Has AM/FM, bluetooth, aux, and USB. Not sure if you'll find...
  
  Apr 4, 2023
- I
  
  INPete replied to the thread Heater box cable clips needed.
  
  If anyone else needs them: https://www.ebay.com/itm/154614129475 These fit just fine
  
  Apr 3, 2023
- I
  
  INPete replied to the thread Heater box cable clips needed.
  
  Thanks, I’ll take a look. I found some for GM products that look the same. Seemed a bit pricey for what they are. But, when you gotta...
  
  Mar 20, 2023
- I
  
  INPete posted the thread Heater box cable clips needed in General Maintenance and Repair.
  
  Doing some dash work and disconnected the heater flap cables from the heater box. One came off, the other broke in half. Can’t seem to...
  
  Mar 19, 2023
- I
  
  INPete replied to the thread Instrument panel lenses very yellow.
  
  Getting it removed was a little tricky for me. Removed the steering wheel which I was replacing anyways. Then I had to remove the...
  
  Mar 16, 2023
Show older items
Loading…
Loading…

Members

Help Support 7173Mustangs.com:

INPete

Latest activity Postings About

Join the conversation!

Register today and take advantage of membership benefits. It's FREE!

Don't like ads?

Did you know that registered members can turn off the ads?