Search results

I installed these. Also running a big aluminum headed 351w stroker. These are nice because my car is low and they are just long enough to be out of the way and short enough to not scrape the ground. They are also ball and socket at the collector so you have some freedom with alignment. Im fuel...

Yo! Don't know if you tried looking into offload parts.... definitely a lot of sway bar fabrication going on there. Here is an example link to kartek, an offload house. Check their website for sway bar stuff. They have many fittings etc...

Yeah, for me, they save so much time. This is mostly because my car sits LOW. so it kinda becomes a pain to get a jack under the front quarter pumping it....... I just got tired of positioning jack stands, necessity.... no bit it sure is a NICEssity! That said, pulled your own measurements, I...

Yeah... i kinda was worried about that too. It actually works perfect, there is an offset however the plate wherebthe blocks go are wide enough to compensate. I think, based on the attached pic of the frame there is something like 1.84 inch difference on each side.... as in the rear subframe is...

Hey Heff.... there are probably more experienced guys than me here that can answer your question.... as my car has the acoustic roll down windows..... That said..... Can you post pics of the bracket you are talking about?

Yep. That makes perfect sense. Thanks ribbs, Will e and rc add1ct!

My windows work, but am hesitant to put my interior back in until I can for sure figure out this piece. I contacted motorcity for a replacement, dunno if he has any yet. looked in the shop manual and couldn't find the part. So anyone who has pics of it or has removed it that has any info would...

Thanks for that info. It looks like it is kinda bent in alittle towards the window. Does is keep this from rattling as well? Or is it's only purpose to support the panel? Thanks all!

Hello! Well, pulled off my quarter panels to get to my rear windows in my 73 coupe. Noticed both sides are missing the little bracket looking thing that is held on with two screws near the felt. I've included a pic I found online for reference. What does this bracket do? Can I make one? Do I...

I'm running the 5000tlx. It's rad because I just park over them and pull them out to line up with the torque boxes when I need to lift them. I built my entire car in the garage, including paint..... these things save so much time. Only downside is you kinda need to crawl in or out from the front...

Thanks RCadd1ct and Don. I agree. I'll run the piece or order the one from Global west that RC mentioned. Thanks all!

Yeah.... I think I'll follow suit here and do the same then. Thanks Tony. For what it's worth.... you have inspired my build many times.

Thanks, not to worried about the bumpstops, the JRI coilovers I'm running have them on the shock already, more concerned about the integrity of the shock tower during hard driving. Thanks! Manny

Hello all! So I'm shaking down my car.... I'm running a maier coilover front end kit. That said I have elected to leave both front coil spring cover/ bump stop mounts off the car. It makes it easier for shock adjustments etc... I've included a pic of the part just to clear up any confusion on my...

Hello! Just installed these two clips that go on the upper weatherstrip moulding. There are two... are they the same? I ordered 4 of them (see pics) just want to make sure I did t screw this up before putting in weatherstrip. My car didn't have these when bought so I have no point of reference...

Thanks... I'll get em hung then. Yeah... the roll bar was installed with the headliner in mind... should be good to go. Probably. Thanks!

Ok... think I got the pic thing figured out. Pics on the post of what I was trying to describe

Hello!!! Ok.... so I'm going to have a local mustang shop pop my headliner in. Question is.... can I install the drip rails and door weatherstrip that goes in the bright aluminum trim pieces above the door first? Or do these pieces need to be off for the headliner install? Or maybe install them...

Hello! I run this guy, it's an AC delco part. Had to modify the stock vapor canister mount alittle but it fits in the stock location. Uses the line running from the tank and one line to ported manifold vacuum. Works great, no smell and readily available. Just an FYI to anyone looking to other...

Hello! I have a rand new 351 Windsor air gap intake manifold (made by Professional Products I think) it's new in box. I went fuel injection and didn't need this manifold. Asking 75.00 plus shipping. Herr is the box weight and dimensions to calculate shipping via an online calculator : Length...