Search results

I’ve been down this road. I have a security system with a key fob and a trunk popper. I made the trunk release latch mechanism with guitar string and the solenoid for the aftermarket trunk popper kit. It worked fine for a while but now I have to push the button a few times before it will...

Lowered price to 500.00

This is where I would start if it were me, seen it more than once.

My Oldest Brother bought a Brand new 72 Mach 1 351 cj golden glow. He is 16 years older than me. I was 8 years old at the time. He is restoring it now. When it came time for me to purchase my first car all I wanted was a car like his. A 72 Mach 1. March /April of 82 I found one in the classified...

I have a brand new still in box tmi one piece headliner for sale. Black charcoal vinyl one piece with sail panels included (black charcoal matches the rest of the tmi interior like dash and seats) https://www.tmiproducts.com/products/1-piece-headliner-1971-73-mustang/ford/mustang/1972 I will...

Looks like others have covered temperature sensor well. I love my sniper. 2 things that may help. After you done if you need help setting IAC( idle air control) there is a Holley produced video on you tube that is very good. Also I ended up installing a progressive linkage on the secondary to...

I purchased a 80 gal 2 stage ingersol Rand from Tractor Supply more than 10 years ago. I recently had to replace the motor. Make sure you have the proper size wire powering the compressor, this may be hard on the motor causing excessive amp draw. I had wore than enough but the motor may fail...

Welcome from a very inactive member. This is what I run, 18x8 245/45/18. Front 18x9 285/40/18 rears. 18x8-4.5” back space front 18x9-5.25 backspacing rear My first car as well owned since 1982- on the road again since summer 2021.

I did this exact setup, I think it works well I have nothing to compare it to. I did have to replace the internal regulator on the sniper with an external one because it would not bring it down to 59lbs. I was wondering if it may have something to do with the volume that pump is moving. Hope...

Well Sorry Guys I haven’t put anything on here in almost 8 years…… the car is pretty much done, painted it last winter And My son is doing well he has given me 2 beautiful grandkids. I will try to start a new thread because tiny pic delete most of my other pics. Tried to add a pic looks like...

I’m in the process of wiring my fans up on a Holley sniper. The sniper can completely control your fans/temp. It uses the Holley sniper temp sensor. There is I believe a light blue and green wires in the accessories harness pigtail on the sniper. These are the grounding side of your relays...

If you look close at this picture. I had to move the connection point up . You can see where I welded it to start with. it acted like it was dragging on the inside of the cylinder a bit at the lower location. Another mistake, confession is good for the soul I guess. When I moved it up I drilled...

There is a jam nut supposed to be used to keep from damaging the master from over stroking. I tried to attach a pdf of the installation instructions.Message me and I’ll try to send it through messaging or email if you want it. I can’t remember but I think I called modern driveline and they told...

Sent from my iPhone using Tapatalk

http://americanpowertrain.com/i-8521624-1971-73-mustang-hydramax-hydraulic-clutch-actuator-system-for-tko-t45-3650-t5-t56-magnum.html I purchaced this—I have not used it , just installed the hydr master cylinder for mock up on the firewall before final finish. I installed mistakenly next to...

Try not to allow rotation of the pad to rotate into blend if you can. Especially if you have some type of blender solution which I don't think you do. You want to rotate off the blend if you are on it at all. Not too much or a visible distinct separation between new paint and old paint will be...

I wont used the clears produced by kirker, I did a full paint on my Sons Dakota in 2008 and it just didn't hold up like it should have over the years. The wise word posted earlier may be true. "you get what you pay for". My Brother/Nephew Has a body shop, been in the business since 76. He used...

Some friends from church go every year and have for decades. Its a family tradition. the go some place near steamboat springs( i think), They hunt private land and pay to hunt, its expensive and they get a deal because they have been going for decades. I have a cousin who has gone and hunted...

Big Loud THANK YOU!!! to Motor City Mustang for getting me a drivers side fender bracket. Saved me lots of time not having to Fab one. :thankyouyellow: Great Vendor.... Great forum Dennis

Welcome, I get into Muncie a couple times a month for work. Welcome back. I am north west of Ft Wayne in Albion / Noble County