’71 Mach 1 Resto Project

7173Mustangs.com

Help Support 7173Mustangs.com:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I couldn't let it go last night, so after we ate dinner, I went out and applied the driver's side hockey stick stripe.

I was going to apply the passenger stripe also, but I decided that I could do that side one night this week after work.


Mach 1 976.jpgMach 1 974.jpg

It really changes the look of the car!

IMO, without the stripe it looks clean and classy, but with the stripe it looks more aggressive and sporty!

As Mickey D's says, I'm loving it! :love:


Mach 1 960.jpgMach 1 972.jpg

Better than it looked almost three years ago, haha. I think it is safe to bring my Tandem bike back up from the basement now. It is a 1969 Schwinn Twinn deluxe that my parents bought new. I had just finished restoring it right before I bought the Mach and I did not want to risk it getting damaged. You can see it hanging from the ceiling of the garage in the before pic of the Mach.

Mach 1 (35).jpg

Here is a before and after pic of the tandem on the ground, I stripped it to a bare frame and painted it House of Kolors, Candy Root Beer with a gold metallic base. It was originally a similar brown, but this color really pops compared to the original color. The picture doesn't give it justice, in the sun the gold base comes alive. Knowing I was going to do some spraying on the Mustang in the garage, I did not want to risk over spray landing on it, so it has been residing in the basement.

Tandem (1).jpgTandem (1a).jpg
 
Last edited:
Put the Mach 1 decals on the side first and take a long look before applying the hockey stick decals. Really a clean look that I prefer, your opinion may vary
I deleted the hockey puck but kept the pinstripe for a clean look.
 

Attachments

  • 71RightFront.jpg
    71RightFront.jpg
    3.6 MB
Thanks, you are right, the joy rides are indeed the pay-off! I am going to try and drive it as much as possible for the next couple months until I need to put her away for the winter. I also plan to store this one in the third bay of my home garage for the winter, as this is my favorite. I have always stored my other cars at my childhood friends home, He and his wife have some high end cars in their climate controlled huge shop out behind their house that they are kind enough to allow me to share. I always offer to pay rent but he always jokes that they're okay and don't need to supplement their income just yet. Considering my cars share their space with their five classic Ferraris, I think they are doing okay, so probably don't need the rent money, haha.
 
I deleted the hockey puck but kept the pinstripe for a clean look.
I agree that is a nice clean look, your car looks incredible like that.

IMO, the awesome pronounced style line from front fender tip to before the rear wheel opening is the star of the show down the side when there is no hockey stick stripe. I just love the look of the stripe though, and I believe that the body line still holds it's own against the stripe when it has to share the attention with the stripes.
 
I got out to the garage and applied the passenger hockey stick stripe last night after work, the car looks awesome! Getting the stripes on makes the car look complete, except of course it still has no bumper or RH mirror, but you hardly notice, haha, right?

I intend to take it to a cruise night on Thursday with some friends and again to the last of this season of a monthly car show near me next Tuesday. Not to be judged of course, it doesn't have a bumper lol, but just to hang with friends and enjoy my latest creation. I still have a punch list to check off before Thursday of little things that need to be done. The usual fluid checks, suspension fastener torque checks, and a couple adjustments.

Mach 1 983.jpgMach 1 984.jpg

I love those body style lines! Once in a while manufacturers get it right, Ford got it right with the 71-73s!

Mach 1 986.jpg


Now, as my traditional finishing touch, I just need to decide on the placement of my "built not bought" decal. I like to place them on all of my cars, haha,

The rear quarter windows would be perfect but I only have one decal and can't remember where I got it so I could get a second matching one.

thumbnail_image0 (3).jpg
 
I got out to the garage and applied the passenger hockey stick stripe last night after work, the car looks awesome! Getting the stripes on makes the car look complete, except of course it still has no bumper or RH mirror, but you hardly notice, haha, right?

I intend to take it to a cruise night on Thursday with some friends and again to the last of this season of a monthly car show near me next Tuesday. Not to be judged of course, it doesn't have a bumper lol, but just to hang with friends and enjoy my latest creation. I still have a punch list to check off before Thursday of little things that need to be done. The usual fluid checks, suspension fastener torque checks, and a couple adjustments.

View attachment 92912View attachment 92913

I love those body style lines! Once in a while manufacturers get it right, Ford got it right with the 71-73s!

View attachment 92914


Now, as my traditional finishing touch, I just need to decide on the placement of my "built not bought" decal. I like to place them on all of my cars, haha,

The rear quarter windows would be perfect but I only have one decal and can't remember where I got it so I could get a second matching one.

View attachment 92915
Lots of those stickers on Amazon
 
I got out to the garage and applied the passenger hockey stick stripe last night after work, the car looks awesome! Getting the stripes on makes the car look complete, except of course it still has no bumper or RH mirror, but you hardly notice, haha, right?

I intend to take it to a cruise night on Thursday with some friends and again to the last of this season of a monthly car show near me next Tuesday. Not to be judged of course, it doesn't have a bumper lol, but just to hang with friends and enjoy my latest creation. I still have a punch list to check off before Thursday of little things that need to be done. The usual fluid checks, suspension fastener torque checks, and a couple adjustments.

View attachment 92912View attachment 92913

I love those body style lines! Once in a while manufacturers get it right, Ford got it right with the 71-73s!

View attachment 92914


Now, as my traditional finishing touch, I just need to decide on the placement of my "built not bought" decal. I like to place them on all of my cars, haha,

The rear quarter windows would be perfect but I only have one decal and can't remember where I got it so I could get a second matching one.

View attachment 92915
Looks great! What's the story on the bumper? I must've missed that post. :unsure:
 
Looks great! What's the story on the bumper? I must've missed that post. :unsure:
Sorry, I thought I mentioned this situation.

My indecision struck again, I kept procrastinating on repairing the bumper, trying to decide what was the best course of action. The original bumper, as you can see in the first pic, was dented and slightly twisted. It doesn't look that bad in the pic, but it was twisted and there were worse dents on the bottom of the bumper. My body men friends were suggesting all types of repair processes, so many I wasn't sure which to follow. By the time I straightened (pic 2) and repaired the bumper the car was painted and partially assembled.

As it sits right now, (pics 3 and 4) the bumper has been body worked, repaired, primered and blocked and I sprayed the final coat of primer on it, Although not perfect, it is pretty straight and is ready for paint. My friend Mike and I just need to find time in both of our schedules when I can get back in the spray booth and paint it. I also need to repaint the passenger mirror base at the same time. I put a run in it when I painted it the first time. I tried to sand out the run, but I sanded through, so I just blocked it down and it is ready to be resprayed. I am hoping now that most of the summer extra curriculars are winding down, we will be able to get a time that works for both of us to let me spray those parts in the near future and get them installed on the car. 🤞

Mach 1 (6).jpgMach 1 (746).jpgMach 1 875.jpgMach 1 876.jpg
 
Sorry, I thought I mentioned this situation.

My indecision struck again, I kept procrastinating on repairing the bumper, trying to decide what was the best course of action. The original bumper, as you can see in the first pic, was dented and slightly twisted. It doesn't look that bad in the pic, but it was twisted and there were worse dents on the bottom of the bumper. My body men friends were suggesting all types of repair processes, so many I wasn't sure which to follow. By the time I straightened (pic 2) and repaired the bumper the car was painted and partially assembled.

As it sits right now, (pics 3 and 4) the bumper has been body worked, repaired, primered and blocked and I sprayed the final coat of primer on it, Although not perfect, it is pretty straight and is ready for paint. My friend Mike and I just need to find time in both of our schedules when I can get back in the spray booth and paint it. I also need to repaint the passenger mirror base at the same time. I put a run in it when I painted it the first time. I tried to sand out the run, but I sanded through, so I just blocked it down and it is ready to be resprayed. I am hoping now that most of the summer extra curriculars are winding down, we will be able to get a time that works for both of us to let me spray those parts in the near future and get them installed on the car. 🤞

View attachment 92943View attachment 92944View attachment 92945View attachment 92946

How did you end up straightening it? Mine is very wavy.
 
I had no idea how I was going to do it, so I reached out to some body men friends for suggestions, I got a bunch of different ideas that ranged from seemingly ineffective to drastic. One guy told me that back in the day they skinned the urethane off of the metal bumper. After that was done, they straightened the bumper with heat and metal finishing like you would on any steel bumper and then re-adhered the urethane to the straightened steel bumper. I didn't want to beat on the urethane, but I definitely didn't want to skin the bumper.

I ended up trying to press it straight. I started with heavy gauge angle iron and big fricking clamps, I sandwiched the bent part of the bumper between two short pieces of heavy gauge angle iron and used a few large clamps (pre-apply grease to the threads and run the thread through to spread it out) to compress the angle iron together with the bumper in between. I had to use pipe wrenches to tighten the clamps at the end. After doing this a few times, the bumper was almost perfect and then I hammered and dollied the remaining dents. Of course because of the gauge of steel my body hammers did nothing, so I used my four pound sledge and adjusted my force keeping in mind the mass of the hammer. Fortunately, it was mostly low spots that needed to be worked out so the majority of hammer hits were to the inside of the bumper. The bumper still was twisted slightly so I clamped it down again with the angle iron and used a big breaker bar and twisted the one end back in inline with the other end. Some times brute force is the correct answer, haha.

I followed that up with grooving out all of the cracks and filling them with a urethane and rubber fascia filler product I got through my friends body shop supplier. After that sanding, primer, sanding again and primer again and now it is ready for final blocking and painting.

thumbnail_IMG_1569.jpg
 
I had no idea how I was going to do it, so I reached out to some body men friends for suggestions, I got a bunch of different ideas that ranged from seemingly ineffective to drastic. One guy told me that back in the day they skinned the urethane off of the metal bumper. After that was done, they straightened the bumper with heat and metal finishing like you would on any steel bumper and then re-adhered the urethane to the straightened steel bumper. I didn't want to beat on the urethane, but I definitely didn't want to skin the bumper.

I ended up trying to press it straight. I started with heavy gauge angle iron and big fricking clamps, I sandwiched the bent part of the bumper between two short pieces of heavy gauge angle iron and used a few large clamps (pre-apply grease to the threads and run the thread through to spread it out) to compress the angle iron together with the bumper in between. I had to use pipe wrenches to tighten the clamps at the end. After doing this a few times, the bumper was almost perfect and then I hammered and dollied the remaining dents. Of course because of the gauge of steel my body hammers did nothing, so I used my four pound sledge and adjusted my force keeping in mind the mass of the hammer. Fortunately, it was mostly low spots that needed to be worked out so the majority of hammer hits were to the inside of the bumper. The bumper still was twisted slightly so I clamped it down again with the angle iron and used a big breaker bar and twisted the one end back in inline with the other end. Some times brute force is the correct answer, haha.

I followed that up with grooving out all of the cracks and filling them with a urethane and rubber fascia filler product I got through my friends body shop supplier. After that sanding, primer, sanding again and primer again and now it is ready for final blocking and painting.

View attachment 92958
Very cool!

Thanks for the info.
 
I got out to the garage and applied the passenger hockey stick stripe last night after work, the car looks awesome! Getting the stripes on makes the car look complete, except of course it still has no bumper or RH mirror, but you hardly notice, haha, right?

I intend to take it to a cruise night on Thursday with some friends and again to the last of this season of a monthly car show near me next Tuesday. Not to be judged of course, it doesn't have a bumper lol, but just to hang with friends and enjoy my latest creation. I still have a punch list to check off before Thursday of little things that need to be done. The usual fluid checks, suspension fastener torque checks, and a couple adjustments.

View attachment 92912View attachment 92913

I love those body style lines! Once in a while manufacturers get it right, Ford got it right with the 71-73s!

View attachment 92914


Now, as my traditional finishing touch, I just need to decide on the placement of my "built not bought" decal. I like to place them on all of my cars, haha,

The rear quarter windows would be perfect but I only have one decal and can't remember where I got it so I could get a second matching one.

View attachment 92915
Nice job! The hockey stick stripes look awesome especially on the white. IMO the stripes give a more muscle car look. I as well agree that no stripes with lower moldings give the car a more classy look. I decided not to go with the stripes with lower moldings because that's over done and incorrect. If my car originally had stripes for sure I would gone that way.
 

Attachments

  • IMG_3241.JPG
    IMG_3241.JPG
    547.4 KB
I had no idea how I was going to do it, so I reached out to some body men friends for suggestions, I got a bunch of different ideas that ranged from seemingly ineffective to drastic. One guy told me that back in the day they skinned the urethane off of the metal bumper. After that was done, they straightened the bumper with heat and metal finishing like you would on any steel bumper and then re-adhered the urethane to the straightened steel bumper. I didn't want to beat on the urethane, but I definitely didn't want to skin the bumper.

I ended up trying to press it straight. I started with heavy gauge angle iron and big fricking clamps, I sandwiched the bent part of the bumper between two short pieces of heavy gauge angle iron and used a few large clamps (pre-apply grease to the threads and run the thread through to spread it out) to compress the angle iron together with the bumper in between. I had to use pipe wrenches to tighten the clamps at the end. After doing this a few times, the bumper was almost perfect and then I hammered and dollied the remaining dents. Of course because of the gauge of steel my body hammers did nothing, so I used my four pound sledge and adjusted my force keeping in mind the mass of the hammer. Fortunately, it was mostly low spots that needed to be worked out so the majority of hammer hits were to the inside of the bumper. The bumper still was twisted slightly so I clamped it down again with the angle iron and used a big breaker bar and twisted the one end back in inline with the other end. Some times brute force is the correct answer, haha.

I followed that up with grooving out all of the cracks and filling them with a urethane and rubber fascia filler product I got through my friends body shop supplier. After that sanding, primer, sanding again and primer again and now it is ready for final blocking and painting.

View attachment 92958
Victory!!
 
I got out to the garage and applied the passenger hockey stick stripe last night after work, the car looks awesome! Getting the stripes on makes the car look complete, except of course it still has no bumper or RH mirror, but you hardly notice, haha, right?

I intend to take it to a cruise night on Thursday with some friends and again to the last of this season of a monthly car show near me next Tuesday. Not to be judged of course, it doesn't have a bumper lol, but just to hang with friends and enjoy my latest creation. I still have a punch list to check off before Thursday of little things that need to be done. The usual fluid checks, suspension fastener torque checks, and a couple adjustments.

View attachment 92912View attachment 92913

I love those body style lines! Once in a while manufacturers get it right, Ford got it right with the 71-73s!

View attachment 92914


Now, as my traditional finishing touch, I just need to decide on the placement of my "built not bought" decal. I like to place them on all of my cars, haha,

The rear quarter windows would be perfect but I only have one decal and can't remember where I got it so I could get a second matching one.

View attachment 92915
Looking so good!! I really like the clean look of the white with black accents!
 
Nice job! The hockey stick stripes look awesome especially on the white. IMO the stripes give a more muscle car look. I as well agree that no stripes with lower moldings give the car a more classy look. I decided not to go with the stripes with lower moldings because that's over done and incorrect. If my car originally had stripes for sure I would gone that way.
I agree that the stripes definitely emit more of a muscle car vibe, but with no stripes the car has a more classy look. If my car came with the decor group lower moldings, I would not have done the hockey stick stripes either. You car looks awesome! I love the red, it fits the body style of our cars so well.
 
Looking so good!! I really like the clean look of the white with black accents!
Thank you! As much I am sure I would have loved the Grabber Blue with black stripes, I absolutely love the Wimbledon White with the black accents. It is such a distinct variation being opposite ends of the spectrum. I think it really makes the stripes and accents pop!
Even my wife has admitted she really didn't get the white black color scheme vision at first, but now that she sees it she is a big fan.
 
I had no idea how I was going to do it, so I reached out to some body men friends for suggestions, I got a bunch of different ideas that ranged from seemingly ineffective to drastic. One guy told me that back in the day they skinned the urethane off of the metal bumper. After that was done, they straightened the bumper with heat and metal finishing like you would on any steel bumper and then re-adhered the urethane to the straightened steel bumper. I didn't want to beat on the urethane, but I definitely didn't want to skin the bumper.

I ended up trying to press it straight. I started with heavy gauge angle iron and big fricking clamps, I sandwiched the bent part of the bumper between two short pieces of heavy gauge angle iron and used a few large clamps (pre-apply grease to the threads and run the thread through to spread it out) to compress the angle iron together with the bumper in between. I had to use pipe wrenches to tighten the clamps at the end. After doing this a few times, the bumper was almost perfect and then I hammered and dollied the remaining dents. Of course because of the gauge of steel my body hammers did nothing, so I used my four pound sledge and adjusted my force keeping in mind the mass of the hammer. Fortunately, it was mostly low spots that needed to be worked out so the majority of hammer hits were to the inside of the bumper. The bumper still was twisted slightly so I clamped it down again with the angle iron and used a big breaker bar and twisted the one end back in inline with the other end. Some times brute force is the correct answer, haha.

I followed that up with grooving out all of the cracks and filling them with a urethane and rubber fascia filler product I got through my friends body shop supplier. After that sanding, primer, sanding again and primer again and now it is ready for final blocking and painting.

View attachment 92958
Very Great Job
 
I took the car for an alignment yesterday, WOW what a difference it made. After tearing down to an empty shell and installing all new front suspension and steering, I knew it was going to be a little off when I reassembled it. The only thing that was off though was the caster, and the camber and the toe, but only on the right side and the left, haha. :ROFLMAO:

Yeah, it was all off, I could tell when I first drove it that everything was fighting itself. When I dropped it off the steering wheel was a little off center and the toe was visibly out on both sides. The car wandered and pulled and followed the road crown badly.

I picked it up and drove it home from the alignment shop and it felt like a completely different car from the one I drove over there. The steering wheel was centered and it drove straight effortlessly, I let go of the wheel and it goes straight down the road.

My son picked me up and took me back to get the car and when we got home he had that "can I drive it" look in his eye. So now that I knew mechanically it was right, I told him to take it for a spin and see how he likes it. He came back and declared that this is his favorite of my cars now, LOL.

Here are two videos of him driving away and returning, sorry about the finger over the corner of the frame in the second video.

I have to say, I do love the sound of the exhaust, it has such a nice rumble to it, but isn't too loud. You feel it as much as hear it, like a Harley with a nice set of pipes.
 

Attachments

  • Video (43).mov
    2.4 MB
  • Video (45).mov
    1.2 MB
Last edited:
I took the car for an alignment yesterday, WOW what a difference it made. After tearing down to an empty shell and installing all new front suspension and steering, I knew it was going to be a little off when I reassembled it. The only thing that was off though was the caster, and the camber and the toe, but only on the right side and the left, haha. :ROFLMAO:

Yeah, it was all off, I could tell when I first drove it that everything was fighting itself. When I dropped it off the steering wheel was a little off center and the toe was visibly out on both sides. The car wandered and pulled and followed the road crown badly.

I picked it up and drove it home from the alignment shop and it felt like a completely different car from the one I drove over there. The steering wheel was centered and it drove straight effortlessly, I let go of the wheel and it goes straight down the road.

My son picked me up and took me back to get the car and when we got home he had that "can I drive it" look in his eye. So now that I knew mechanically it was right, I told him to take it for a spin and see how he likes it. He came back and declared that this is his favorite of my cars now, LOL.

Here are two videos of him driving away and returning, sorry about the finger over the corner of the frame in the second video.

I have to say, I do love the sound of the exhaust, it has such a nice rumble to it, but isn't too loud. You feel it as much as hear it, like a Harley with a nice set of pipes.
The sequential taillights are a nice touch! (In video two).
 
Back
Top