Search results

Hi my new mustang upholstery doesn't fit. i took the upper back seat all apart and went to put the new one on. the new one is too short length-wise. it is about 4 inches too short. is it actually supposed to stretch that far? the box says 71-73, the pattern is correct. did NPD screw up. help...

Hi, can anyone tell me what the factory used to separate the rear upper seat from the trunk? when i took the interior apart there was a piece of tar paper there held up by duct tape. whatever the part is, do any of the aftermarket companies reproduce it? Thanks All. Thomas Hanson

Hi, anyone know of regular old seat covers i can put on the front buckets of my 72 mach until i can get around to reupholstering them? thanks. Thomas Hanson

Hi, a need to replace the bushings in my sloppy shifter. problem is, even with the front up on ramps i can't get my old age gut under the car to undo the linkage. does anyone know how i can get under there OR can i somehow replace the bushings without disconnecting the linkage? thanks. Thomas...

Hi, I am replacing the carpet in my 72 mach 1, can't get the front kick panels off. all my manuals say there are two screws, one at top that holds the top of the kick panel and the bottom of the upper trim on and a screw lower in the middle. mine only has the top screw, i can't see any others...

Hi, what is a good upholstry brand? NPD uses TMI but they have jacked their prices way up. interior standard upholstry set is $80 more than it was a few years ago. CJ Pony parts sells TMI but also Distinctive Industries. Are they a good product? does anyone know of any other brands i could...

I just put on an NPD ram air setup, followed the directions in an old mustang monthly magazine, everything looks the same as what they did. when I compare it to a pic of a factory ram air setup from a1972 mustang test in an old magazine, which showed an engine pic, it isn't the same. I was...

Hi i have a 1972 Mach 1 with standard interior, nothing but arm rest and door handle, am trying to get door panel off but seems like armrest is preventing me, there are screw holes on the bottom of the arm rest but it doesn’t look screws in there, can someone tell me how to get the door panel /...

Ok, this may be a dumb question but, i have been running un-leaded in my 1972 mustang (that is why i bought a 72, i didn't want to mess with lead additives).  I was looking at the 72 owners manual to see what octane was recommended and it says that all 1972s are designed to operate on "regular"...

Hi, is there anyone in the general area of Quakertown, PA  that knows where i can get gas without ethanol?  i know the Wawa up by I80 has it but that is a little too far to go for gas.  Thanks for the help. BTW, for those of you who were helping me with the idling/stumbling problem, whoever...

Is it ok to blow out the carb passages with the canned compressed air?

I have been buying parts from ebay and aftermarket to convert my sportsroof rear quarter windows to roll-down. I have questions and as Mad Max would say "you have the knowing of a lot of things".  i have bought supposed complete sets and a lot of parts and pieces plus aftermarket stuff (but i...

On the 351c Q code, is the longer choke tube (The one that goes to the vacuum fitting on the carb) Supposed to be loose where it connects to the manifold under the choke? Thanks TCH

Hi, i have a 72 Q code ram air. I want a good maintenance free carb I can just slap on that will work with the ram air. Any suggestions? Thanks  Thomas Hanson’s

Sorry, i should have know better.   The car was sitting for about 3 years.  i started it a few times to get the engine warmed.  starts ok, idles ok at 16 on the vacuum  guage.  i had a friend replace the upper gasket on the the carb because he said it was causing a vacuum leak.  now, car won't...

Hi, i have a 1972 351 Q code, it starts Nad idles ok Vacuum guage is steady at 16, but when i try to Take it for a drive it keeps stalling out Any ideas would be greatly appreciated, thanks Thomas

Does anyone know of a good place to get my 72 mach Repaired in the Quakertown, PA area besides the Mustang Barn? They are good but won’t fix things They just want to replace things, Thanks

Ok, got the new fuel tank and sending unit in, what is the best way to clear rust out of the line without anyone around to help?  And, why are my fuel lines 3/8 and the little hose in the new fuel filter box 1/4 internal ID? Is it because NPD is sending me filters in boxes for 1967 390 and my...

Go to pure-gas.org to find a station near you. Thomas

Is there any easy way? Thanks Thomas