Boss 351 Intake

[bill diehl]

Intake D1ZX-9425-DA for my NHRA stock eliminator Boss 351 project...must be mint, no grinding

 

[Boss1Ray]

They show up on the Boss 351 section of this Boss 302 page but they are usually pricey!

http://www.boss302.com/smf/

Or try these guys - again pricey...

http://www.perogie.com/

Good luck!

Ray

 

[bill diehl]

They show up on the Boss 351 section of this Boss 302 page but they are usually pricey!

http://www.boss302.com/smf/

Or try these guys - again pricey...

http://www.perogie.com/

Good luck!

Ray

Thanks Ray, I am aware that they are made out of gold too, but..... I have to have one as the NHRA did not approve my request to substitute the Blue Thunder

 

[c9zx]

Have you tried posting here? http://classracer.com/classforum/forumdisplay.php?f=12

Chuck

 

[bill diehl]

Have you tried posting here? http://classracer.com/classforum/forumdisplay.php?f=12

Chuck

Yes, I have tried everywhere, I have got some leads from various folks but still no luck in finding anything anywhere

 

[MeZapU]

I thought there was 1-2 on eBay a few weeks ago.

 

[Boss1Ray]

This one is close but it is for a 4300 spreadbore carb. You are wanting the intake that was sold across the parts counter for use with the Holley carb. I only post to help she the difference.

http://www.ebay.com/itm/1971-Ford-351-351C-Boss-Buddy-Bar-aluminum-intake-manifold-/221670845643?pt=Race_Car_Parts&hash=item339c9caccb&vxp=mtr

Ray

 

[bill diehl]

This one is close but it is for a 4300 spreadbore carb. You are wanting the intake that was sold across the parts counter for use with the Holley carb. I only post to help she the difference.

http://www.ebay.com/itm/1971-Ford-351-351C-Boss-Buddy-Bar-aluminum-intake-manifold-/221670845643?pt=Race_Car_Parts&hash=item339c9caccb&vxp=mtr

Ray

yes Ray, that is correct the spreadbore or CA is available from several places...the DA or Holley pattern is impossible to find.

 

[Carolina_Mountain_Mustangs]

I don't know if this guy has what you need but he has lots of performance parts for Ford. SOHC, Tunnel Port 289, 427 etc. I would give him a call.

Greg Shelton 559-333-6013

Good luck,

David

 

[c9zx]

DSC Motorsports or Carl's Ford parts have a lot of connections and may be able to help find one. Want ad in National Dragster??? Just a thought. Chuck

 

[MeZapU]

What about one of these from SCM? Only thing is the part number is a bit different.

http://www.scmenginedevelopments.com/manifolds.html

 

[bill diehl]

What about one of these from SCM? Only thing is the part number is a bit different.

http://www.scmenginedevelopments.com/manifolds.html

It has to be a ford part number that is listed in the blueprint specs, or approved aftermarket and for the Boss combo there are only 3 manifolds allowed. I have talked to Scott about his manifolds, or modifying the core as the cross section is smaller than the ford factory part and I can not modify the manifold at all once cast. In my application it will not work, the BT HP is what I need but I was shot down when I submitted it for approval

 

[bill diehl]

I am also interested in a D1ZZ-9425-G

 

[MeZapU]

eBay auction listing.

 

[4mm]

Did you find one? I have a near mint one that I would be willing to trade for a CA true B351 manifold or partial trade for a blue thunder.