Search results

Well I have the front aprons and radiator support welded on no just need to do the rear and apron extensions. I used dynacorn aprons and they don't have the holes for the clips for bolting the fenders on. So I will have to figure that out the I also need to patch the cowel . Here is what it...

Looking for a radiator support new are around 130 to 180 I am on a budget so used will do I also need the sheet metal that is welded to the cowel and the fender aprons they don't reproduce these I need both sides. Any help is greatly appreciated I would be willing to barter also I have a stock...

where do I get this sheet metal that welds to the Cowl and rear fender apron and where do you get the bracket that the good hinge bolts to on the out side of the apron? also does any one remake the splash Shields I need the drivers side front that starches to the radiator support? also a dumb...

Is it possible to replace crankshaft and bearings on the engine stand with heads on?

I need a set of used door jambs preferably no rust cut from the middle of rear window on forward. Let me know if its possible and how much with shipping to 68136 omaha

Is any one a member in the mach 1 club I forgot my username and am wondering if someone can look me up its miklein or mkleins29 or something of that nature please can someone look me up and reply it should be one of only a few members in Omaha nebraska

4v intake manifold 150.00 Harmonic balancer 20.00 2v heads 120.00 Timing chain cover 20.00 Exauhast manifolds 25.00 New Pro comp electronics ignition wires 10.2mm red 1 boot needs recrimped 30.00 Pics also flex plate new in box 40.00 block plate 20

Just put a air gap intake on and wanting to sell my cast iron one. Figured I would give you guys first dibs before posting on eBay. I am looking to get around 175 for it with the bolts and valley pan. I also have a set of 2v heads for 125 a flex plate new in box for 40 a block spacer for 20 all...

1972 cobra jet casting but its a two bolt main 2 v block and mains 250.00 2v heads 100.00 Crankshaft 125.00 Edlebrock 2 v intake 100.00 Holley 650 double pumper 100.00 Manifolds 30.00 Flywheel 50.00 Block plate 20.00 Rods and pistons 50.00 Sorry about the repost two books were wrong...

Holley 650 double pumper 100 could use a freshening up Edlebrock performer rpm intake 2v 125.00 Cobra jet four bolt main block from 72 good shape 350.00 Crankshaft 125.00 Rods and pistons 50.00 Harmonic balencer 30.00 Exhaust manifolds 50.00 Flywheel new in box 50.00 Block plate 25.00...

For sale 2 valve heads 125.00 Performer edlebrock intake 2v 125.00 Holley 780 do carb 100.00 Crankshaft 125.00 72 cobra jet 4 bolt main block with mains 350.00 Exhaust manifolds 50.00 Brand new in box fly wheel 50.00 Block plate 25.00 Rods used 50.00 All prices negotiable and shipping...

Do these cars have a clutch position switch and what does the rod do that goes from column to 4 speed shifter linkage

According to the wire diagram the red wire and blue stripe connects to s terminal and red with green stripe is I terminal however with a new ignition switch adjusted properly and starter solenoid turn key and no crank over. Swithch the two wires and turn key just out of locked position to run...

I need a good short block I can just throw my heads and stuff in and go or a good 4 bolt rebuild able pm me with what you have need asap

So I have replaced 4 rear mains and still leaking crank was turned .010 bearings look good rope seal changed to other setup roll pin gone I staggered the gaps of the seals the only thing I have not done was replace the oil pan. One machine shop says the line bore must be out of alignment and to...

Finally found a cool remember the times diner pic that has our car it only cost 20.00 with shipping.

I have a short throw hurst shifter with reverse lock out with the linkage looking to get $250 obo it works great i have it on my car right now. I am switching to the original style hurst that should be here tomorrow. I will be switching this weekend. This shifter is great for drag racing I have...

Stock cleveland valve covers 50.00 obo Black Base bezal without gauges from a 71 in good condition 35.00 obo Ford starter barely used 30.00 obo 71 mustang alternator for v8 20.00 used painted black obo

HI have been in the wire diagram section but cant find radio color codes what are the wires can someone please tell me instead of referring me to the diagram s. I need to know which wires are the power wire,ground normally black,the dash light wire for radio, front speaker, my car originally...

Decided to sell this rear window with defrost it is in great condition no chips or anything. I have researched pricing and due to how rare these are i think $350 is a fair price. I would also be willing to trade for the quarter window roll down conversion kit, or a shelby taillight conversion...