Time for a little update
Unlike in most of the world where summer has arrived fr ages, even with crazy high temps, seasons are here locked to October. rain, rain and low temps.
That to say, that in a rare weekends when weather was okish(dry) I went enjoy my 73... well that too, isn't really true at least until a few weeks back..
My Holley Sniper was acting weird for a while and as said in my last post, I bought an external regulator and needed to have the time to install it.
Well, it was a good move because all my issues are gone. from the first test install, where the pressure is to be set, it looks like the pressure was way too high, 72ish vs the 59.5 psi expected by the unit. So once a few tests were done with temp lines, I needed to spend some time to install this properly... and go test drive over a few weeks to see if the problem would return. So far, not a single issue since install..
View attachment 90728
After 2 blank installs to test each lines (feed and return), As I did not wanted to make holes into the firewall and also did not wanted to replaced the breaded hose that was in place for just a few months, I did pick the location where on 73, there is this piece of plastic for vacuum connection that I no longer use for years. so removed it and made a bracket that would bridge nicely. And could cut the line I had. For my 429, I'll install one of these right away but probably else where.
View attachment 90727
In past weeks the 71 project did not stay still. I did lots of things like enjoying to the max for hours the removal of excessive ancient glue/kit stuff from my rear window moldings.
I did not even come to polishing/dents fixing for these, I was simply tired to look at them after this ungratefull task! Took ages as thinner, acetone did nothing and it had to be tediously removed bits by bits! :O
View attachment 90726
the plan was to turn the car around for weeks, but as mother nature served us only rain for weeks, one thing that needed be done is to remove the rest of the paint from the roof. The rest was already done. If you wonder why I remove 4 layers of ancient paint this way: it makes no noise (something my neighbors like) and much less of a mess in my little garage. Tho fun is something else!!
While I did not find anything on the 1/2 roof done previously, on the right front side, I have discovered some ancient repair using bondo and even rust!! :O
View attachment 90725
Once the bondo was removed, the rust turned out to be almost nothing. The metal has some small creases/dents, deep enough to explain the bondo as a repair, as you need to "spoon" from behind and remove the interior/head liner. In my case ofc, no issue with that! So used my self made spoon (and ancient file bended to go places no finger/dolly can go) and after a few session of carefully hammering/spooning, brought the lows back to where they should be. There is so little diff now, that a bit charged sprayed layer of primer should suffice to cover it completely.
View attachment 90724
Another little thing; on the rear window lip, passenger side, no matter the excess of kit being used, the water had found its way, and there were 2 places that needed attention, or better said: a small chirurgical intervention. So cut these sick places, made templates with excess (to trim later), sprayed some zinc and zapped in some strong zincor metal. Poof: like new!
View attachment 90723
Eventually a day with no rain and my "help people" available came so I finally could push the car on street, turn it and push it back in to start the next chapter of the body restoration: fixing the rusty rear! Much better light and of course my tools/bench near!
View attachment 90722
Time to get to work: the most rear part of the trunk floor is crispy and so is the taillight panel...
Plan from 3 weeks ago was to remove the tail panel... but turns out no less than 79 spot welds needed be drilled among other things... The poor thing might be in a bad shape, it was amazing how hard it fought me to finally let go! My back demanded me to do this in 2 steps!
View attachment 90721
The last 10 cm / 3'' were the toughest. Somehow that poor thing, still healthy there, didn't want to let go and I had to be a real man to persuade it!
View attachment 90720
Because last weekend the weather decided to be seasonal unlike past weeks. I did what I wanted do for a while: clean up the fold down. The idea, obviously, was to remove the dirt, but mainly to see if I will need to change the carpet or not. Few hours later with loads of soap/washing machine stuff and elbow oil, got it so far that no coloured water came out. And put the 3 part of the fold down dry in the sun. Once dry, it was clear that 2 are ok, one is discoloured by the sun. So chances are I will replace them unless I find some kind of pigment/ink for this as the carpet on itself is in good shape. The metal needs plating, so will do this during the winter. I needed have it appart and clean first anyway...
View attachment 90719
This weekend I've returned to the 71, next patient: The trunk floor. My back didn't really enjoy the idea at first, but eventually after seeing the percentage of rust on my car diminishing every bits I was removing, I found the motivation and in few hours the rusted to death metal was out. Well most of it... I first drilled from behind to make sure I wouldn't cut anything structural and cut in between dots. The real fun was yet to come, as it was so rusty, there was no way to locate the spot welds! ::O
View attachment 90718
Expecting more corrosion horrors I was actually surprised by 2 things: first the frame is in excellent shape. As if it was zinc coated. In many places it's as new, there is only light rust that will be gone in no time as soon as it meets my acid...
![Big grin :D :D](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
The second good news is that the metal of the floor is healthy at the second V transversal frame piece. Still have the original paint underneath too. So this means less work! As I was planning to remove the fold down structure, which won't be necessary. I should be able to weld the new part on 1/2 that frame lip and obtain very strong bind.
But before I even start do this. I have have plenty more to do in the drop-offs regions...
All with all I've been busy here and there and the project enters a new chapter!
To be continued...