Parts Wanted Clutch fork, Z-Bar and Drive Shaft needed for my Top Loader

[td71mach1]

I have acquired everything except the Z-Bar setup, Clutch Fork and Drive Shaft to install the Top Loader in my 71 Mach1.
I know they now reproduce the Z-Bar setup but I rather buy from a member if one is available.
Clutch fork is scarce as hens teeth, but it never hurts to ask.
FYI... This is a C6 back to original Top Loader conversion
Thanks for looking...Tony

 

[Bobby]

Try these....

If you need a bell housing, I have a cast iron one available.

Ford Mustang Torino Fairlane Cougar Galaxie Toploader 4 Speed Clutch Fork #3 | eBay

NEW 1971 1972 1973 FORD MUSTANG 302 351C BOSS 351 CLUTCH LINKAGE Z BAR KIT | eBay

 

[td71mach1]

Bobby, I have a Lakewood bellhousing, but thanks for the offer.
and I'll check out the links you provided.

 

[Bobby]

Bobby, I have a Lakewood bellhousing, but thanks for the offer.
and I'll check out the links you provided.

Are you going concourse?

 

[td71mach1]

Going Resto-Mod, Old school on the outside and go fast mods under the skin.
Like to do some autocross time and an occasional trip to National Trails Raceway.

 

[351c1971]

JEGS has 3 clutch forks listed, see attached file:

 

[Bobby]

Going Resto-Mod, Old school on the outside and go fast mods under the skin.
Like to do some autocross time and an occasional trip to National Trails Raceway.

I “upgraded “ to a AOD from a C6 when I had my 393c stroker built because the 4 speed top loader option was more expensive. After all the hell I’ve had with that AOD I’m going toploader anyway. I’m using a clutch cable system instead of the z-bar. I got an OEM Ford aluminum bell housing. I’ll have to have an aluminum tab welded to the bellhousing to support the end of the clutch cable. You might be able to get the driveshaft you need at CJ Pony. they have a variety of aluminum and steel shafts. Here is an OEM yoke that also might work for you.

63 64 65 - 73 NOS FORD 28 SPLINE SMALL BLOCK SIZE DRIVE SHAFT YOKE D2ZZ 4841 A | eBay

 

[rcadd1ct]

I went with a malwoodusa pedal and a McLeod throw out bearing.

that being said I do have a z bar somewhere that I am not using…..

 

[rcadd1ct]

And here is one new…..

https://www.npdlink.com/product/bar...s=Z-bar&top_parent=200001&year=1972&year=1972

 

[dawson357]

Hey Tony, did you ever find an original z-bar? If not, I have one that I reconditioned. Been blasted, painted with Cast Blast, rod holes filled in and redrilled. I'd sell it for $100 which about what I've got in it, plus shipping.

 

[td71mach1]

Hey Dawson, I did find a complete z-bar setup but thanks for the offer.
However, I do still need a clutch fork , if you happen to have one for sale.
It seems most of the after market ones are to short.

 

[dawson357]

Hey Dawson, I did find a complete z-bar setup but thanks for the offer.
However, I do still need a clutch fork , if you happen to have one for sale.
It seems most of the after market ones are to short.

You're right. Not easy to find but I'll keep a look out.

 

[rcadd1ct]

This work?

https://www.summitracing.com/parts/sdm-pce633-1001/make/ford