Jump to content

Parting out 72’ Sportsroof 2F02H100534 - Near Weed CA


Recommended Posts

Rear window glass $70, Drivers side quarter window glass $20 and passenger side door window glass $70.  I would consider shipping the quarter window, others would have to be pickup only.
 

Standard dash- no plastic or harness.  Comes with glove box door.  local pickup- no shipping.  Has more rust than most on the inside from the car having no windshield, but no rot.  Should clean up with a blast or dip  $30

Radiator is marked FoMoCo D1AF GA 1FC End tank is smashed from accident - fins are bent and it is covered in Ringtail cat poo as the radiator lying flat in the trunk with the shroud was apparently prime ringtail real estate.  I pay you $5 to take it.

 

13416C75-BDF1-45CF-A200-ABAB606C820E.jpeg

E2454BED-1417-4156-89A2-3425B60BE4BA.jpeg

Edited by Bentworker
Link to comment
Share on other sites

@Bentworker given the rust through on the passenger floor, I think I know the answer, but I'm going to ask anyways.  I'm looking for an intact cowl tank for an A/C car. Also, both door hinge plates for the driver-side upper hinge.  These are the backing plates that the hinge bolts screw into (inside the pillar and inside the door).

Thanks,

Nick

Link to comment
Share on other sites

Does the car have an FMX transmission?   Im looking for the electrical plug terminal connecter  (on the main wiring harness)  that the Shifter Neutral safety switch plugs into.

My car has been rewired and sadly I don't have that connecter.

Also looking for the 2 front centre grille support plates in front of the radiator support panel (not the long ones, the 2 shorter black plates)

Thanks Mark

mustang rad plates.jpg

Edited by 92GTS-R
Link to comment
Share on other sites

22 minutes ago, 92GTS-R said:

Does the car have an FMX transmission?   Im looking for the electrical plug terminal connecter  (on the main wiring harness)  that the Shifter Neutral safety switch plugs into.

My car has been rewired and sadly I don't have that connecter.

Also looking for the 2 front centre grille support plates in front of the radiator support panel (not the long ones, the 2 shorter black plates)

Thanks Mark

mustang rad plates.jpg

I’m not positive on the plates.  I should be able to go look at the car Friday, my guess is that they may be smashed.  
 

It is an FMX car, and the harness is intact.  I could FaceTime you next time I am at the car so the right part of the harness gets pruned.

Link to comment
Share on other sites

If the drivers side door switch is a three prong ford part I’d be interested in it, also the driver side mirror.

Link to comment
Share on other sites

The neutral safety switch conversation is giving me deja vu.  I remember our '71 being like @Bentworker's and having only the two connectors (white and black), but couldn't recall why.  

I'm hoping this is the answer.  According to West Coast Classic Cougar, there was a running change made 12/1/1971 from the 2 connector to the 3 connector. https://secure.cougarpartscatalog.com/c9zz-7a247-c-used.html?a=GoogleProductSearch&gclid=EAIaIQobChMIrqy75Zjm6wIVtBx9Ch1SagOZEAQYCCABEgIZ7PD_BwE&pk_campaign=689785599&pk_content=154423720703&pk_kwd=&pk_medium=cpc&pk_source=GoogleAds&sessionthemeid=26

Good luck,

Nick

Link to comment
Share on other sites

BTW, big thanks to @Bentworker on the hinge plates (farther up in this thread).  Here they are after a little cleanup.  Aside from my clumsiness dropping the plate down the pillar, they worked great.  We now have a working driver door.  

Here's a few tips if you're replacing the top plates on a mostly assembled car:

  • Tie a piece of thin twine through the top bolt hole on the pillar plate and tie the other end off to something stationary.  If you drop the plate, you can always just pull it back up and try again.
  • Have a helper on the outside guide you and be ready to put a bolt into one of the plate bolt holes (they can see, you can't)
  • While you're there, replace all the bolts.  In my case, I snapped all 3 trying to loosen them so I didn't have a choice.
  • Oh, and on the door side plate, that's a 3/8" square drive hole in the middle.  Use a 3/8" ratchet to help persuade the plate into place.

Best,

Nick

2020-09-13_06-23-54.png

  • Like 1
Link to comment
Share on other sites

  • 3 months later...

Items still available for local pickup near Weed CA.

Rear window (small scratches, but better than many) $70

Standard dash $free

Door shells ($200/ each) Would clean up nice with a blast or dip. They do have holes where the trim is secured.

3.00 open Ford 9” complete with parking brake cables $300)

 

The shell is  going to the scrapper in a week or three.  If there is anything you see in the photos that you may want inquire here and I will post a price for whatever catches your eye.  Keep it in mind that nearly everything inside is junk because it had no windshield for 18 years outside in the weather.

 

Link to comment
Share on other sites

57 minutes ago, 72MustangSprint said:

Do you still have the rear valence ? It looks good in the pic. If so price and shipping to 37160, thx

If he doesn't have it available, I have one in good condition.

---

Mike

Link to comment
Share on other sites

2 hours ago, 72MustangSprint said:

Do you still have the rear valence ? It looks good in the pic. If so price and shipping to 37160, thx


I still have the rear valance, and it is in nice shape.  I’m not excited about the idea of boxing it up since it is so big.  If Mike is willing to ship his I’d say go for it.   I’d want $100 plus actual shipping cost or $80 local pickup.  I’ll be back home at the end of the week and can measure it up and get you a shipping estimate if you don’t strike up a deal with Mike.

Link to comment
Share on other sites

7 hours ago, Bentworker said:


I still have the rear valance, and it is in nice shape.  I’m not excited about the idea of boxing it up since it is so big.  If Mike is willing to ship his I’d say go for it.   I’d want $100 plus actual shipping cost or $80 local pickup.  I’ll be back home at the end of the week and can measure it up and get you a shipping estimate if you don’t strike up a deal with Mike.

I might have found one so if that falls through then we can figure out if Mike wants to ship.

Edited by 72MustangSprint
adpic.jpg
Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...