Parting out 72’ Sportsroof 2F02H100534 - Near Weed CA

Help Support 7173Mustangs.com:

Bentworker

VIP Members
Joined
Jan 17, 2015
Messages
1,507
Reaction score
204
Location
California
My Car
71' Grande project.
@TheRktmn

We’re good.  I still have your address from when you did my tach.  Once I get it out I’ll PM you the shipping cost.

 

Bentworker

VIP Members
Joined
Jan 17, 2015
Messages
1,507
Reaction score
204
Location
California
My Car
71' Grande project.
@73MustangCoupe

I got the disk brake spindles from my buddies shop today.  
 

While they look crusty the area of the spindle that normally gets screwed up from bad bearings is Very good on these.  You can feel some ridges with your fingernail where the inner race contacted the shoulder of the spindle.  Spindles should clean up nicely once you get the gunk off.  Also the upper ball joint, lower ball joint and tie rod areas have little to no hammer damage.   I know the car these came off of and it was not wrecked, just a rust bucket.

  Rock shields are hammered.  

Rotor / hubs were one piece aftermarket ones and went in the scrap pile - not available.
 

Calipers are crusty but may be rebuildable.

$120 plus shipping for the pair with or without the calipers.

7043AA73-4E1B-4E84-A66C-97D6BFE539FE.jpeg

4681003B-B3D9-46B0-81A6-B9EBB780C866.jpeg

749AA37A-FABF-4395-A566-D5900C23D740.jpeg

 

73MustangCoupe

VIP Members
Joined
Jul 5, 2013
Messages
955
Reaction score
270
Location
Jonesborough, TN
My Car
1973 Mustang Mach 1
Hey Bentworker,

That sounds good.  Please PM me and let me know how we can settle up, and I can get you my shipping address.

Ron

 

92GTS-R

VIP Members
Joined
Aug 29, 2019
Messages
402
Reaction score
44
Location
North Surrey UK
My Car
1971 Mustang 302 V8
Thanks for the door pics, I did not realise it had the extra trim on the outside of the door, I presume the trim is attached to the door using screws through the outer door skin.  Im looking for a clean door with no holes. Sorry.

 

MikeGriese

VIP Members
Joined
Dec 24, 2013
Messages
819
Reaction score
123
Location
Minnesota
My Car
71 convertible
Don't give up on the horns.  I am finding a few hours in an ultrasonic cleaner brings them back to life.

 

MikeGriese

VIP Members
Joined
Dec 24, 2013
Messages
819
Reaction score
123
Location
Minnesota
My Car
71 convertible
I can't tell from the photos, but do the calipers still have the cylinders in them?

 

Bentworker

VIP Members
Joined
Jan 17, 2015
Messages
1,507
Reaction score
204
Location
California
My Car
71' Grande project.
Rear window glass $70, Drivers side quarter window glass $20 and passenger side door window glass $70.  I would consider shipping the quarter window, others would have to be pickup only.
 

Standard dash- no plastic or harness.  Comes with glove box door.  local pickup- no shipping.  Has more rust than most on the inside from the car having no windshield, but no rot.  Should clean up with a blast or dip  $30

Radiator is marked FoMoCo D1AF GA 1FC End tank is smashed from accident - fins are bent and it is covered in Ringtail cat poo as the radiator lying flat in the trunk with the shroud was apparently prime ringtail real estate.  I pay you $5 to take it.

13416C75-BDF1-45CF-A200-ABAB606C820E.jpeg

E2454BED-1417-4156-89A2-3425B60BE4BA.jpeg

 
Last edited by a moderator:

Bentworker

VIP Members
Joined
Jan 17, 2015
Messages
1,507
Reaction score
204
Location
California
My Car
71' Grande project.
The car has the 2 barrel variable Venturi carb on it if anyone wants it.

 

knn

Well-known member
Joined
Aug 27, 2017
Messages
112
Reaction score
13
Location
San Francisco, CA
My Car
1971 Mach 1 (302)
@Bentworker given the rust through on the passenger floor, I think I know the answer, but I'm going to ask anyways.  I'm looking for an intact cowl tank for an A/C car. Also, both door hinge plates for the driver-side upper hinge.  These are the backing plates that the hinge bolts screw into (inside the pillar and inside the door).

Thanks,

Nick

 

Bentworker

VIP Members
Joined
Jan 17, 2015
Messages
1,507
Reaction score
204
Location
California
My Car
71' Grande project.
@knn

I have the hinge plates.  I took a borescope and looked into the cowl- I cant make out for sure one way or the other on condition.  Will have to wait until I take the dash the rest of the way apart.

 

Bentworker

VIP Members
Joined
Jan 17, 2015
Messages
1,507
Reaction score
204
Location
California
My Car
71' Grande project.
@knn

I took a closer look at the cowl today- it is rotted out junk.

I have the upper drivers side hinge plates and can put them in a small USPS flat rate box.  If $20 shipped sounds okay PM me your address.

 

92GTS-R

VIP Members
Joined
Aug 29, 2019
Messages
402
Reaction score
44
Location
North Surrey UK
My Car
1971 Mustang 302 V8
Does the car have an FMX transmission?   Im looking for the electrical plug terminal connecter  (on the main wiring harness)  that the Shifter Neutral safety switch plugs into.

My car has been rewired and sadly I don't have that connecter.

Also looking for the 2 front centre grille support plates in front of the radiator support panel (not the long ones, the 2 shorter black plates)

Thanks Mark

mustang rad plates.jpg

 
Last edited by a moderator:

Bentworker

VIP Members
Joined
Jan 17, 2015
Messages
1,507
Reaction score
204
Location
California
My Car
71' Grande project.
Does the car have an FMX transmission?   Im looking for the electrical plug terminal connecter  (on the main wiring harness)  that the Shifter Neutral safety switch plugs into.

My car has been rewired and sadly I don't have that connecter.

Also looking for the 2 front centre grille support plates in front of the radiator support panel (not the long ones, the 2 shorter black plates)

Thanks Mark

View attachment 44179
I’m not positive on the plates.  I should be able to go look at the car Friday, my guess is that they may be smashed.  
 

It is an FMX car, and the harness is intact.  I could FaceTime you next time I am at the car so the right part of the harness gets pruned.

 

midlife

Shorts checker
Joined
Jan 24, 2012
Messages
4,073
Reaction score
483
Location
Tucson, AZ
My Car
No Mustangs at the moment.
I have those connectors galore if Bentworker's aren't good.

 

ChrisH

VIP Members
Joined
Jun 21, 2018
Messages
77
Reaction score
7
Location
US
My Car
1973 Mach1, Q code, 4 speed, with an open 3:25 differential. It has what is left of the original Gold Glow paint and a very sun baked ginger interior. I purchased it in Winslow Arizona in May 2018. It has a 75 DSO and I believe it spent its entire time in AZ. It appears to have been parked in 1978 until earlier this year when the guy I bought it from purchased it.
If the drivers side door switch is a three prong ford part I’d be interested in it, also the driver side mirror.

 

Bentworker

VIP Members
Joined
Jan 17, 2015
Messages
1,507
Reaction score
204
Location
California
My Car
71' Grande project.
@92GTS-R

The wiring down the tunnel has one less connector than the picture you posted.

@ChrisH

Sorry- I am keeping the mirror and switch.

D6F89060-9971-4AC2-A78C-B8101D06E1AD.jpeg

 
Top