Loud Violent Clunk When Shifting FMX Into Gear. Any Transmission Experts?

7173Mustangs.com

Help Support 7173Mustangs.com:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

andy72

Well-known member
Joined
Jul 3, 2014
Messages
253
Reaction score
23
Location
california, ca
My Car
1972 mach 1 351 ram air
[url=https://ibb.co/R9rNbJs][img]https://i.ibb.co/376vdPj/DSC06636.jpg[/img][/url]
Hello Everyone,
I posted this same problem about a year ago but dads health caused me to step away from the car.
I'm going to start over here...

When I shift into gear, especially Reverse, the car has a loud clunk and a violent jerk. It feels like it wants to break something.
What I've done/tested...

351C FMX transmission
Timing 6 BTDC
Idle in Park about 700
new U Joints
Transmission had a fluid replacement and is full.
The car had sat stationary outside for years before I got it in 2015.
It has shifted like this as long as I've owned it.

I disconnected the drive shaft from the rear end and supported it up. No clunk when shifting into gear.
With shaft reconnected, I got under the car and clearly the noise comes from the rear end.
I find it hard to believe its the rear though because I have a 460 with a C6 and a 302 with a C4.
In either of these cars, if I give a little gas to increase RPM to about 800, neither car clunks at all when shifting into gear or jerks so bad like my 72.
Both of those cars just shift into gear like butter virtually noise and sensation free.
The 72 shifts into gear and jerks the car and has a loud clunk.
My 67 with 9 inch Equa-lock seems to have more slop in rear end if I jack tire off ground and rotate axle.
Not sure if this is actually a valid test of rear end slop, but I did it.

Is it possible the FMX is shifting into gear improperly and rotating the drive shaft harder or with more force than it should?
It does this shifting into Reverse or Drive, but it is worse shifting into reverse.
I feel like if I replace the third member the car is going to do the same thing.
Please watch vide below to see and hear the issue.

Any thoughts?
Thank you
 

Attachments

  • 20240630_114543.mp4
    44.5 MB
Hello Everyone,
I posted this same problem about a year ago but dads health caused me to step away from the car.
I'm going to start over here...

When I shift into gear, especially Reverse, the car has a loud clunk and a violent jerk. It feels like it wants to break something.
What I've done/tested...

351C FMX transmission
Timing 6 BTDC
Idle in Park about 700
new U Joints
Transmission had a fluid replacement and is full.
The car had sat stationary outside for years before I got it in 2015.
It has shifted like this as long as I've owned it.

I disconnected the drive shaft from the rear end and supported it up. No clunk when shifting into gear.
With shaft reconnected, I got under the car and clearly the noise comes from the rear end.
I find it hard to believe its the rear though because I have a 460 with a C6 and a 302 with a C4.
In either of these cars, if I give a little gas to increase RPM to about 800, neither car clunks at all when shifting into gear or jerks so bad like my 72.
Both of those cars just shift into gear like butter virtually noise and sensation free.
The 72 shifts into gear and jerks the car and has a loud clunk.
My 67 with 9 inch Equa-lock seems to have more slop in rear end if I jack tire off ground and rotate axle.
Not sure if this is actually a valid test of rear end slop, but I did it.

Is it possible the FMX is shifting into gear improperly and rotating the drive shaft harder or with more force than it should?
It does this shifting into Reverse or Drive, but it is worse shifting into reverse.
I feel like if I replace the third member the car is going to do the same thing.
Please watch vide below to see and hear the issue.

Any thoughts?
Thank you
That is wild. Is your idle RPM really 700? Do you have a Detroit locker in it?

Reason I ask about the Detroit is that they have a clunk by design. It is normal with a Detroit to have a 60 degree ish amount of rotational slop between forward and reverse at the driveshaft.

On the engine RPM, the video didn’t look like 700 rpm to my eye. If you have a timing light with a tach second check your idle RPM.
 
Last edited:
Have you checked the play in the differential? If it doesn't do it with the driveshaft removed, then you've eliminated everything forward of the driveshaft. You say the u-joints are good so you've eliminated them. Time to check the play in the diff, I'd say. Mine had significant play in it after 40-some years; it's not unusual for cars as old as these to develop some slop in the ring and pinion gears.
 
First off, rotating the wheels back and forth while jacked up is not typically a valid test for excessive rear-end free play (unless something is radically wrong). I'd suggest getting your car up on a shop's lift and isolate this noise with a stethoscope and dig in from there. Another alternative is using an electronic noise sensor to zero in on that noise. Good luck with it!
 
so "72 Conv"...
You say you had a shot differential that would produce such a pronounced loud clunk that can make a car jolt?
That's what I want to know...

No Detroit locker. Just an open 9 inch with 3.25's.
I have a lift. I've been under the car with my hands on the rear end while my son shifts. It is definitely the rear end making the clunk.

As I said, I can rev my other 2 cars to higher RPM than this, about 1000 rpm, shift into gear and they don't clunk like this!

I've had people mention the torque converter as a potential problem. ?
It just engages reverse and drive so hard that it makes me wonder if anything can go wrong in the tranny to do this.
I've had numerous Mustangs in the family. Been around cars my whole life. Friends with cars. Everyone says "Wow, something not right"
 
You might have a stall converter, when my C6 was rebuilt the guy put a stall converter in and if I put it in gear without my foot on the brake it will chirp the tires in the garage. In other words it bangs pretty hard. The 9 inch rear end is hard to break but it is something to check also.
 
When you disconnected the driveshaft, did you restrain it from rotating or did it just spin freely when trans was put in gear? If it wasn't restrained, the test would seem to provide only minimal info and doesn't really eliminate the trans from the root cause.

That being said, the rear diff is more likely the problem. WIth the rear wheels restrained (either on the ground or e-brake firmly holding) and driveline removed, rotate the pinion yoke back and forth. The spec on ring gear backlash is .008-.012"...don't know what that translates to in in degrees of yoke rotation, but it's not a lot. you should not be able to move the pinion yoke, other than the small amount of rotation due to backlash. Excessive backlash would likely come from the small pinion gears that run on the splined side gears (the ones that make it a differential). I've seen the support shaft worn badly from getting the vehicle stuck and spinning one wheel for a relatively long time....even worse if the axle was tilted and all the oil ran to one side. Doing long one-wheel burnouts will smoke these gears/shaft too. That's my best guess.

1719841860676.png
 
Sounds like play in the rear end. You should be able to hear it more pronounced at the rear of the car
 
When I disconnected the driveshaft, I supported it up with mule tape so it would spin freely. I understand that this is not a great test of anything, but it did show me that the noise wasn't coming strictly from the transmission itself being put into gear.

As I said it my original post, my 67 seems to have more rear end slop simply by rotating a wheel that is off the ground. I can disconnect the driveshaft from both my 72 and my 67, leave the wheels down on my 4 post lift, and see which one has more slop in the pinion. This will at least compare the two although I'm not sure this provides a definitive answer.

As I said before, I was really hoping that a transmission person could say that "this or that" (transmission problem) could produce that problem.
I doubt that it has a stall converter installed. Can the converter itself be a contributing problem? Everything I read online says a bad torque converter will slip. My car has an opposite problem. A loud bang when it engages gear.
I just find it hard to believe that the huge "jerk" or "jolt" I get is just rear end slop. All old Mustangs have old sloppy rears from 50 plus years on the road and they don't bang like this.

Frustrated

 
Can you feel and or hear where it is? With the wheels on the ground and trans in neutral, how much rotation is there in the driveshaft? Are your motor mounts and transmission mount in good condition?
When driving the car, does it shift normally into 2nd and 3rd gears?
 
When I disconnected the driveshaft, I supported it up with mule tape so it would spin freely. I understand that this is not a great test of anything, but it did show me that the noise wasn't coming strictly from the transmission itself being put into gear.

As I said it my original post, my 67 seems to have more rear end slop simply by rotating a wheel that is off the ground. I can disconnect the driveshaft from both my 72 and my 67, leave the wheels down on my 4 post lift, and see which one has more slop in the pinion. This will at least compare the two although I'm not sure this provides a definitive answer.

As I said before, I was really hoping that a transmission person could say that "this or that" (transmission problem) could produce that problem.
I doubt that it has a stall converter installed. Can the converter itself be a contributing problem? Everything I read online says a bad torque converter will slip. My car has an opposite problem. A loud bang when it engages gear.
I just find it hard to believe that the huge "jerk" or "jolt" I get is just rear end slop. All old Mustangs have old sloppy rears from 50 plus years on the road and they don't bang like this.

Frustrated

Post up what you find when you put it up on the 4 post…
 
When I disconnected the driveshaft, I supported it up with mule tape so it would spin freely. I understand that this is not a great test of anything, but it did show me that the noise wasn't coming strictly from the transmission itself being put into gear.

As I said it my original post, my 67 seems to have more rear end slop simply by rotating a wheel that is off the ground. I can disconnect the driveshaft from both my 72 and my 67, leave the wheels down on my 4 post lift, and see which one has more slop in the pinion. This will at least compare the two although I'm not sure this provides a definitive answer.

As I said before, I was really hoping that a transmission person could say that "this or that" (transmission problem) could produce that problem.
I doubt that it has a stall converter installed. Can the converter itself be a contributing problem? Everything I read online says a bad torque converter will slip. My car has an opposite problem. A loud bang when it engages gear.
I just find it hard to believe that the huge "jerk" or "jolt" I get is just rear end slop. All old Mustangs have old sloppy rears from 50 plus years on the road and they don't bang like this.

Frustrated

Your 3rd member needs to be gone thru and rebuilt. New bearings, probably new pinion gears and shaft, etc. Possibly a new ring and pinion if too much wear is noted. Might be worth considering ordering a new assembly.
 
So I put the car up on my lift, put it in neutral as suggested, and rotated the driveshaft.
Watch the 2 videos.
Doesn't seem like alot of rotation/play to me, but it has more of a "clunk" than the 2nd video.
The 2nd video (aluminum driveshaft) is my 67. It has way more rotation/slop but a different sound to it.

Yes the motor mounts are good. Yes it shifts fine to 2nd and 3rd.
As stated, I reved my 67 up to 1000rpm, dropped it into gear and it doesn't jerk or bang at all!
 

Attachments

  • 20240702_143323.mp4
    16.2 MB
  • 20240702_144826.mp4
    15.7 MB
Interesting. I’d say it is worth draining the rear axle and taking a look.

For what it is worth here are two videos. One is of the 9” in my mustang with 3.50 gears and a trutrac. Less than 1000 miles. Very little play compared to yours. (Top video with the aluminum bearing support)

Other video is of an old Toyota 8” rear axle out of a pickup with lots of hard miles on it, and it still has considerably less play than yours. It has slop in axle splines and spider gears (open differential).

I can’t say for sure that your rear end is the issue, but chances are high. Does not help that Ford did not engineer in a drain plug.


View attachment IMG_5581.mov
View attachment IMG_5579.mov
 
so "72 Conv"...
You say you had a shot differential that would produce such a pronounced loud clunk that can make a car jolt? That's what I want to know...
Some of the gears in the diff were missing teeth! They were actually skipping. The diff was a weak link in that car, and I replaced it several times during the time I owned it.
 
I don’t know if you have had a chance to road test it. To continue on with Don’s idea of it being bad modulator. One sure fire indication the modulator is screwed up is if it downshifts “hard” as you slow down. The modulator actuates under high engine vacuum (like decelerating with the throttle baldes closed) and reduces line pressure to soften transmission operation. Same is true at idle.

Check the vacuum line for holes/ obstructions and check that the modulator itself will hold a vaccum with a mightyvac hand pump (or similar). Insects or other critters may have made the hose not solid or open hose… Make sure it is connected to manifold vaccum and not ported vaccum.

You can also remove the modulator and bench test it with a vacuum pump noting how much vaccum it takes to start retracting the pin / fully retract the pin.

https://7173mustangs.com/threads/fmx-valve-body-info.39371/
 
Back
Top