What did you do to your car today?

70cobrascj · Oct 3, 2024

Been a busy few days here at the home garage resto shop.

Touched up the roof and drivers quarter and fenders. Got the deck lid back from blasting and epoxy primed. Have to spot prime one fender and work a few small low spots on the doors and re-spot prime them. I plan to drop off the hood next week and have it blasted and powder coated since it so large and I won’t have to worry about hurry up and prepping it and prime it before it starts to rust. Hopefully get it to my buddies shop in a couple weeks and get some color on it.
Running low on daylight and warm weather.
I have never done bodywork or painting before and boy what a job it is.
Been enjoying the learning experience for sure.

70cobrascj · Oct 3, 2024

Decided to drop off the hood today instead of next week. Also putting what I hope is the final coat of primer on this fender.

rhigg1959 · Oct 4, 2024

Resealed the 3rd member on my 9" rear end. Good thing I did. During the restoration a few years ago, whomever did the rear end left the oil slinger out.
Prepping the car to sell soon.

tpj71mach · Oct 4, 2024

70cobrascj said:
Decided to drop off the hood today instead of next week. Also putting what I hope is the final coat of primer on this fender. View attachment 93710 View attachment 93711 View attachment 93712 View attachment 93713 View attachment 93714

Looking great! seems like you will be spraying color in not time at all! Can't wait to see it.

The convertible on the rotisserie at the media blaster, is that an Impala? It looks like an early 70's Impala to me. Really nice metal work though on the previous repair, haha. Can't hardly see where the metal was patched.

70cobrascj · Oct 4, 2024

Yes it’s an Impala and it looked good before they blasted it.

tpj71mach · Oct 5, 2024

70cobrascj said:
Yes it’s an Impala and it looked good before they blasted it.

Haha, funny how they always do look like they are solid before we blast them.

I can't be too critical of whoever did that previously though, as I am guilty of the "rivet sheet metal and bondo over it" process back in the day before I could weld.

HeavyCoupe · Oct 30, 2024

Today was the first real drive after the transmission rebuild. It shifts wonderfully. The transmission got 5 forward clutches, 5 direct instead of the 3 and 3 it had. It still has 4 reverse. Changed out the forward drum piston for a newer style with the lip seal versus the square cut seal. I added a B&M shift kit and their thick cast aluminum pan so it holds around 14 quarts of fluid now. The torque converter was rebuilt and given a slightly higher stall by PTC. I also put new bushings in the shifter. It's amazing how much of a difference that made.

There weren't any obvious problems with it other than dumping tons of fluid after sitting for a few days. I assumed there was an issue around the pump seal causing that. I was wrong. In fact the tail housing was cracked causing the leak. We believe this was caused by the broken motor mount. The transmission mount had pulled loose on one side as well. There were internal issues after all. The forward drum piston seal had hardened, bypassing fluid and letting the clutches slip. I couldn't tell it yet but she was on her way out. I'm just glad to be back on the road. Now I have to fix the leaking pinion seal. Fingers crossed the spare 9 inch has a good ratio and I can just swap it in. Wish me luck.

Joeaus08 · Oct 31, 2024

Today, looked at it as I left for work and sighed.

But recently, I replaced the bushing in the torque convertor, front pump, gasket o-ring and front seal. While it was out installed a Fairbanks shift kit and added a Chrome pan that holds 2 extra quarts of fluid. Also, cleaned it up and painted the housing. I know, the headers need attention next. They are on the list.

It is a 351C Q-code with a C6 trans.

What did you do to your car today?

Help Support 7173Mustangs.com:

70cobrascj

Well-known member

70cobrascj

Well-known member

rhigg1959

Well-known member

tpj71mach

Well-known member

70cobrascj

Well-known member

tpj71mach

Well-known member

HeavyCoupe

Well-known member

Joeaus08

Member

Attachments

Similar threads

Latest posts

What did you do to your car today?

Help Support 7173Mustangs.com:

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Member

Attachments

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!