- Joined
- May 19, 2021
- Messages
- 1,653
- Reaction score
- 1,184
- My Car
- 73 Grande will be used to build 73 Vert.
It’s like POR 15, but it includes a variation in language when your hand slips and the wire wheel catches your leg.
1973 Convertible Project: Engine Bay Restoration
- Thread starter Steve McMahan
- Start date
Help Support 7173Mustangs.com:
- Joined
- Jan 24, 2012
- Messages
- 4,599
- Reaction score
- 1,468
- Location
- Tucson, AZ
- My Car
- No Mustangs at the moment.
POR 15 is a "Paint Over Rust" converter which is a bitch to remove once applied. Lots of folks like it; I do not because it can hide a lot of rust and is extremely difficult to remove to see the actual damage.
- Joined
- May 19, 2021
- Messages
- 1,653
- Reaction score
- 1,184
- My Car
- 73 Grande will be used to build 73 Vert.
I’m into denial
- Joined
- May 19, 2021
- Messages
- 1,653
- Reaction score
- 1,184
- My Car
- 73 Grande will be used to build 73 Vert.
Ok, so I’m at that point where I have to decide what treatment I'm going to give the undercarriage. Last week I was 100% certain I wanted to do a bed-liner treatment over the POR-15. Today, I’m hedging my bet. Mostly because of the stories I’ve been reading on-line what other cars guys will interpret I did, or didn’t do, to the restoration of the body pan. I read those before and kinda shrugged them off, but now I’m reconsidering.
Let me make clear how I intend to use this car, and maybe beyond the stupid self-inflicted opinion of my work, will help others give me an informed opinion on what would be the logical treatment to do. This will be my fun to drive car. It will be garaged in Fort Mohave, Az, a very dry climate with very little rain. I don’t see myself driving it in the rain, but it could happen. I also won’t likely wash it a lot; I believe like @Hemikiller that washing is generally unnecessary (I hope I quoted him correctly). I like the look of the bed-liner more than I care for the additional toughness it gives the pan from road objects.
What is your advice?
Let me make clear how I intend to use this car, and maybe beyond the stupid self-inflicted opinion of my work, will help others give me an informed opinion on what would be the logical treatment to do. This will be my fun to drive car. It will be garaged in Fort Mohave, Az, a very dry climate with very little rain. I don’t see myself driving it in the rain, but it could happen. I also won’t likely wash it a lot; I believe like @Hemikiller that washing is generally unnecessary (I hope I quoted him correctly). I like the look of the bed-liner more than I care for the additional toughness it gives the pan from road objects.
What is your advice?
- Joined
- Aug 5, 2019
- Messages
- 2,533
- Reaction score
- 2,931
- Location
- Texas
- My Car
- 72 Mustang Q-code
70 Mach 1 M-code
Check out Lizardskin coatings. They apply easily and don't have the rough finish of bed liner and traditional undercoating.
- Joined
- Apr 14, 2019
- Messages
- 586
- Reaction score
- 379
- Location
- Center Valley , PA18034
- My Car
- 72 Vert 351C White
Maybe do nothing. If it's original metal and really no rust
- Joined
- Jan 24, 2012
- Messages
- 4,599
- Reaction score
- 1,468
- Location
- Tucson, AZ
- My Car
- No Mustangs at the moment.
In your AZ environment, undercoating is not needed, even if you drive in the rain on occasion. You're unlikely to encounter salted roads, which is where undercoating can pay dividends (in the Northeast/Midwest).
- Joined
- Jul 12, 2010
- Messages
- 5,475
- Reaction score
- 3,762
- Location
- Killingworth, CT
- My Car
- 71 Mach 1
71 XR-7 hardtop
71 Country Squire
65 hardtop
72 Country Sedan
69 XL sportsroof
I wire wheeled the under side of my 71, just like you, then applied POR15 from the torque boxes back and that was it. I did apply some spray on undercoating in the rear wheel wells. The front clip was painted with primer and then catalyzed satin black enamel. This was in 2003-ish.
FWIW, the POR15 paint that everyone uses is not a rust converter, it's a moisture cured urethane paint. They recommend their MetalReady beforehand, which is a phosphoric acid based rust remover / converter. I've found the MR to be very handy to keep around for lots of general rust removal and prep tasks.
FWIW, the POR15 paint that everyone uses is not a rust converter, it's a moisture cured urethane paint. They recommend their MetalReady beforehand, which is a phosphoric acid based rust remover / converter. I've found the MR to be very handy to keep around for lots of general rust removal and prep tasks.
I was more worried about the inside of the frame rails than the floor pans. I wire brushed the floor pans inside and outside and painted them with black enamel. The wheel wells were coated with rubberized undercoating. Finally, the inside of the frame rails and doors was sprayed with Eastwood Rust converter.
- Joined
- May 19, 2021
- Messages
- 1,653
- Reaction score
- 1,184
- My Car
- 73 Grande will be used to build 73 Vert.
Yea, I’m ordering the Eastwood inside frame spay can, with the hose. I used a rod of silver solder with Emory cloth on one end to make a sanding drum to try and clean where it couldn’t reach, using my drill motor with it for extra cleaning. That was an adventure.
Last edited:
IMHO the Eastwood inside frame spay can with the hose is also an adventure. The hose works well...until it clogs. I advise shaking the can well before each use.
Also keep in mind that undercoating is needed to protect the area under the front fender where there is no wheel house from road stone dings.
- Joined
- May 19, 2021
- Messages
- 1,653
- Reaction score
- 1,184
- My Car
- 73 Grande will be used to build 73 Vert.
I’ve got the fenders off to do a thorough job on them. I only want to do this once.
- Joined
- Aug 17, 2019
- Messages
- 406
- Reaction score
- 273
- Location
- Fort McMurray, Alberta
- My Car
- '73 Vert with 4R70W
351C Ram Air 2V 441 hp @ 6000 RPM
SEFI EEC-V (2004)
9" trac-loc limited slip 3.5:1
P-Zero 265/35ZR-19's front 305/30ZR-19's rear
Sounds like Por15 would be overkill for your car just like it is for mine. I embarked on my project with less than half the knowledge I needed. Por15 is for projects that have rust involved in the metal already. If you are going down to bare metal I wouldn’t waste the time or energy. If you are worried about rusting inside any frame rails perhaps you might want the Por15 inside them but not on anything you take down to bare metal.
- Joined
- May 19, 2021
- Messages
- 1,653
- Reaction score
- 1,184
- My Car
- 73 Grande will be used to build 73 Vert.
Too late. I’ve got 1/2 of it already in POR-15. I’m sure it’s overkill. It’s like HP. Is there ever enough?
After the inputs, and thinking it over, what I would like to do, over the POR-15, is to finish it with a nice treatment. Not quite a bed liner toughness, but with a textured to the finish, and a satin black color. What does that sound like to you guys?
After the inputs, and thinking it over, what I would like to do, over the POR-15, is to finish it with a nice treatment. Not quite a bed liner toughness, but with a textured to the finish, and a satin black color. What does that sound like to you guys?
- Joined
- Aug 14, 2014
- Messages
- 4,542
- Reaction score
- 1,588
- Location
- Madison, WI
- My Car
- 1971 Mach 1 w/408C stroker
The hose is pretty much a one time use item. I have tried cleaning them to use afterwards but it is hit-or-miss. Just be aware that if the line clogs and the nozzle comes out, it can shoot paint back towards you or other surfaces. It is very liquid so it will drip from every little hole in the frame so make sure you are ready to collect the drip.
- Joined
- Aug 17, 2019
- Messages
- 406
- Reaction score
- 273
- Location
- Fort McMurray, Alberta
- My Car
- '73 Vert with 4R70W
351C Ram Air 2V 441 hp @ 6000 RPM
SEFI EEC-V (2004)
9" trac-loc limited slip 3.5:1
P-Zero 265/35ZR-19's front 305/30ZR-19's rear
If you have the Por15 on already you will need to scratch it up because nothing adheres to it. I made the same mistake when I was priming the bottom of my car. I let the first coat dry 24 hours before putting on a second coat (which is totally unnecessary by the way). I should have read the instructions a bit closer to see that a second coat should go on when the first is tacky. If memory serves the instructions are to sand it with 200 grit if you let the top coat dry. Incidentally, if you like the look of the Por15 primer, they sell a Top Coat Clear that will retain that wet black look. Once I finish wire-wheeling the welds to my shock towers I am going to scuff up the engine bay on mine and touch up the grinding marks with Por15 and spray on the Top Coat Clear. In any event you will need to finish it with something because the black will fade when exposed to sunlight if you don't Top Coat it.
- Joined
- May 19, 2021
- Messages
- 1,653
- Reaction score
- 1,184
- My Car
- 73 Grande will be used to build 73 Vert.
Yea, I knew I had to sand it with 300 beforehand. I just didn’t have the schedule to do it all together. So, the clear coat does the same finish like clear on paint? Anyone apply a texture kind of paint?
- Joined
- May 19, 2021
- Messages
- 1,653
- Reaction score
- 1,184
- My Car
- 73 Grande will be used to build 73 Vert.
How about the Mastercoat stuff? Is it any better regarding the need to prep it before painting over it? I just realized I have a quart can I purchased this time last year. I’m already committed to completing the POR-15 on the bottom of the car. But, I’ve not started on the engine compartment. Could I scuff that paint, put the Mastercoat over that, and then like a satin black paint over that?
Today, I completed the wire-wheel on the unibody, up to the engine compartment. Tomorrow, I’ll apply the POR-15 from the rear axle to the trans tunnel. My plans after that are, move the car off the wheel cribs, put it up on my highest jack stands, remove front and rear suspensions (one at an time due to available space), and complete the wire wheel cleaning of those areas and the wheel wells. I hope I can get all that done by the end of next week. Thanks.
Today, I completed the wire-wheel on the unibody, up to the engine compartment. Tomorrow, I’ll apply the POR-15 from the rear axle to the trans tunnel. My plans after that are, move the car off the wheel cribs, put it up on my highest jack stands, remove front and rear suspensions (one at an time due to available space), and complete the wire wheel cleaning of those areas and the wheel wells. I hope I can get all that done by the end of next week. Thanks.
- Joined
- Jul 12, 2010
- Messages
- 5,475
- Reaction score
- 3,762
- Location
- Killingworth, CT
- My Car
- 71 Mach 1
71 XR-7 hardtop
71 Country Squire
65 hardtop
72 Country Sedan
69 XL sportsroof
IMO, you can simply clean up the engine compartment, spot prime any bare metal spots and spray it with a low gloss black paint. The POR/Mastercoat/RustBullet paints don't lay out flat enough in my opinion.
Similar threads
