What did you do to your car today?

[Totalled]

Rock auto has new PM starters for $57.99

 

[clevelandcoupe]

attachment=7855]

Sand blasted and sprayed POR 15 on the front section of Mach 1.

Can't wait until I can get some color on it so I can reassemble the suspension parts I have already painted. Need to get car rolling so I can bring model a home again !!!

 

[Steven Harris]

It is only a starter, driveshaft, shifter knob and boot away from being a manual trans car. I can't wait for the first drive selecting gearss myself!

About time to have rocketfoot update your signature banner!

-------------------------

Hey Clevelandcope - NICE!

 

[Qcode351mach]

Got the new qtr on this morning..Now to line everything up & get r done !

 

[droptop73]

Nice work Scott.

 

[user 915]

Replaced quite a few exterior bulbs, and then the dimmer switch so I could drive home from work, lol. Then found out I will either need to replace some interior bulbs or my headlight switch so I can see how fast I am going at night....

 

[mach71351c]

Been busy detailing truck and 5th wheel for vacation. So the Mach1 had been put on hold.Today I had some time so I cut the rust out of the right quarter. After looking at both sides I need to order outer wheel houses to move froward.Hope to get back on it in 3 weeks.

 

[Mister 4x4]

Despite all the free vendor-sponsored beer I just had, I'm SO Jonesin' to work on my pile.

Can't wait for Saturday!

 

[jeremycfr]

Got the new qtr on this morning..Now to line everything up & get r done !

Did you use a full 1/4 or a skin?

 

[user 915]

Just replaced the signal flasher and i now have working signals that i dont have to operate by hand manipulation!

 

[73vertproject]

Just replaced the signal flasher and i now have working signals that i dont have to operate by hand manipulation!

::goodjob::

Doc

 

[Qcode351mach]

Ok got the otr fitted nice..decklid nice..rear body panel nice..Just need to put the rear glass & moldings on to check that fit & then I can index mark..sheet metal screw everthing together..Then weld-r-up

 

[M Beauchamp]

Ok got the otr fitted nice..decklid nice..rear body panel nice..Just need to put the rear glass & moldings on to check that fit & then I can index mark..sheet metal screw everthing together..Then weld-r-up

looking good Q

 

[Qcode351mach]

Ok got the otr fitted nice..decklid nice..rear body panel nice..Just need to put the rear glass & moldings on to check that fit & then I can index mark..sheet metal screw everthing together..Then weld-r-up

looking good Q

Thanks M..A bunch of extra work & expense but worth it for sure

 

[sm3570]

Talked to the body shop today...it's official, she's going in a week from tomorrow!!! ::chili:: ::beer:: :banana: ::chili::

When she's out of the garage I can work on the seat upholstery. :-/

 

[not2old]

HEARD ENGINE POP THEN NOTICED OLW OIL PRESSURE AND GAUGE IRRATIC. GOT HOME AND CHECKED OIL LEVEL AND FOUND 2QTS LOW. FIRST OIL CHANGE AFTER BREAK-IN SO NOT TOO CONCERNED, SOME OIL USE COULD BE NORMAL AT BREAK-IN (BEING POSITIVE). AFTER START UP OIL PRESSURE NORMAL AND NO ABNORMAL ENGING NOISES.

WILL CONTINUE USING BREAK IN ADDITIVE

ALAN L

 

[marks73]

Did you prime it first?

 

[Tnfastbk]

Got the car back tonight, got my new vent from Don and going tomorrow to put the rear louvers on.

 

[Qcode351mach]

Got the car back tonight, got my new vent from Don and going tomorrow to put the rear louvers on.

Adams time for sure..You need the Americana carnuba..http://www.adamspolishes.com/p-423-adams-americana-premium-carnauba-paste-car-wax.aspxPut on 1 coat a day for 3 days..

Stand back & drool...Sun glasses required for sure ..Just let me know R..

 

[71_badmach]

Man, I was going to say how shiny and purdy it was... it gets better than that?